from small one page howto to huge articles all in one place

Other .linuxhowtos.org sites:toolsntoys.linuxhowtos.org
gentoo.linuxhowtos.org

poll results

Last additions:

words:

887

views:

195651

userrating:

average rating: 1.7 (102 votes) (1=very good 6=terrible)

May 25th. 2007:

Words

486

Views

252057

why adblockers are bad

Workaround and fixes for the current Core Dump Handling vulnerability affected kernels

words:

161

views:

140921

userrating:

average rating: 1.4 (42 votes) (1=very good 6=terrible)

April, 26th. 2006:

Words

Views

100785

New subdomain: toolsntoys.linuxhowtos.org

You are here: manpages

openvpn

Section: Maintenance Commands (8)
Updated: 25 August 2016
Index Return to Main Contents

NAME

openvpn - secure IP tunnel daemon.

SYNOPSIS

openvpn [ options ... ]

INTRODUCTION

OpenVPN is an open source VPN daemon by James Yonan. Because OpenVPN tries to be a universal VPN tool offering a great deal of flexibility, there are a lot of options on this manual page. If you're new to OpenVPN, you might want to skip ahead to the examples section where you will see how to construct simple VPNs on the command line without even needing a configuration file.

Also note that there's more documentation and examples on the OpenVPN web site: http://openvpn.net/

And if you would like to see a shorter version of this manual, see the openvpn usage message which can be obtained by running openvpn without any parameters.

DESCRIPTION

OpenVPN is a robust and highly flexible VPN daemon. OpenVPN supports SSL/TLS security, ethernet bridging, TCP or UDP tunnel transport through proxies or NAT, support for dynamic IP addresses and DHCP, scalability to hundreds or thousands of users, and portability to most major OS platforms.

OpenVPN is tightly bound to the OpenSSL library, and derives much of its crypto capabilities from it.

OpenVPN supports conventional encryption using a pre-shared secret key (Static Key mode) or public key security (SSL/TLS mode) using client & server certificates. OpenVPN also supports non-encrypted TCP/UDP tunnels.

OpenVPN is designed to work with the TUN/TAP virtual networking interface that exists on most platforms.

Overall, OpenVPN aims to offer many of the key features of IPSec but with a relatively lightweight footprint.

OPTIONS

OpenVPN allows any option to be placed either on the command line or in a configuration file. Though all command line options are preceded by a double-leading-dash ("--"), this prefix can be removed when an option is placed in a configuration file.

--help

Show options.

--config file

Load additional config options from file where each line corresponds to one command line option, but with the leading '--' removed.

If --config file is the only option to the openvpn command, the --config can be removed, and the command can be given as openvpn file

Note that configuration files can be nested to a reasonable depth.

Double quotation or single quotation characters ("", '') can be used to enclose single parameters containing whitespace, and "#" or ";" characters in the first column can be used to denote comments.

Note that OpenVPN 2.0 and higher performs backslash-based shell escaping for characters not in single quotations, so the following mappings should be observed:

\\       Maps to a single backslash character (\).
\"       Pass a literal doublequote character ("), don't
         interpret it as enclosing a parameter.
\[SPACE] Pass a literal space or tab character, don't
         interpret it as a parameter delimiter.

For example on Windows, use double backslashes to represent pathnames:

secret "c:\\OpenVPN\\secret.key"

For examples of configuration files, see http://openvpn.net/examples.html

Here is an example configuration file:

#
# Sample OpenVPN configuration file for
# using a pre-shared static key.
#
# '#' or ';' may be used to delimit comments.

# Use a dynamic tun device.
dev tun

# Our remote peer
remote mypeer.mydomain

# 10.1.0.1 is our local VPN endpoint
# 10.1.0.2 is our remote VPN endpoint
ifconfig 10.1.0.1 10.1.0.2

# Our pre-shared static key
secret static.key

Tunnel Options:

--mode m

Set OpenVPN major mode. By default, OpenVPN runs in point-to-point mode ("p2p"). OpenVPN 2.0 introduces a new mode ("server") which implements a multi-client server capability.

--local host

Local host name or IP address for bind. If specified, OpenVPN will bind to this address only. If unspecified, OpenVPN will bind to all interfaces.

--remote host [port] [proto]

Remote host name or IP address. On the client, multiple --remote options may be specified for redundancy, each referring to a different OpenVPN server. Specifying multiple --remote options for this purpose is a special case of the more general connection-profile feature. See the <connection> documentation below.

The OpenVPN client will try to connect to a server at host:port in the order specified by the list of --remote options.

proto indicates the protocol to use when connecting with the remote, and may be "tcp" or "udp".

For forcing IPv4 or IPv6 connection suffix tcp or udp with 4/6 like udp4/udp6/tcp4/tcp6.

The client will move on to the next host in the list, in the event of connection failure. Note that at any given time, the OpenVPN client will at most be connected to one server.

Note that since UDP is connectionless, connection failure is defined by the --ping and --ping-restart options.

Note the following corner case: If you use multiple --remote options, AND you are dropping root privileges on the client with --user and/or --group, AND the client is running a non-Windows OS, if the client needs to switch to a different server, and that server pushes back different TUN/TAP or route settings, the client may lack the necessary privileges to close and reopen the TUN/TAP interface. This could cause the client to exit with a fatal error.

If --remote is unspecified, OpenVPN will listen for packets from any IP address, but will not act on those packets unless they pass all authentication tests. This requirement for authentication is binding on all potential peers, even those from known and supposedly trusted IP addresses (it is very easy to forge a source IP address on a UDP packet).

When used in TCP mode, --remote will act as a filter, rejecting connections from any host which does not match host.

If host is a DNS name which resolves to multiple IP addresses, OpenVPN will try them in the order that the system getaddrinfo() presents them, so priorization and DNS randomization is done by the system library. Unless an IP version is forced by the protocol specification (4/6 suffix), OpenVPN will try both IPv4 and IPv6 addresses, in the order getaddrinfo() returns them.

--remote-random-hostname

Prepend a random string (6 bytes, 12 hex characters) to hostname to prevent DNS caching. For example, "foo.bar.gov" would be modified to "<random-chars>.foo.bar.gov".

<connection>

Define a client connection profile. Client connection profiles are groups of OpenVPN options that describe how to connect to a given OpenVPN server. Client connection profiles are specified within an OpenVPN configuration file, and each profile is bracketed by <connection> and </connection>.

An OpenVPN client will try each connection profile sequentially until it achieves a successful connection.

--remote-random can be used to initially "scramble" the connection list.

Here is an example of connection profile usage:

client
dev tun

<connection>
remote 198.19.34.56 1194 udp
</connection>

<connection>
remote 198.19.34.56 443 tcp
</connection>

<connection>
remote 198.19.34.56 443 tcp
http-proxy 192.168.0.8 8080
</connection>

<connection>
remote 198.19.36.99 443 tcp
http-proxy 192.168.0.8 8080
</connection>

persist-key
persist-tun
pkcs12 client.p12
ns-cert-type server
verb 3

First we try to connect to a server at 198.19.34.56:1194 using UDP. If that fails, we then try to connect to 198.19.34.56:443 using TCP. If that also fails, then try connecting through an HTTP proxy at 192.168.0.8:8080 to 198.19.34.56:443 using TCP. Finally, try to connect through the same proxy to a server at 198.19.36.99:443 using TCP.

The following OpenVPN options may be used inside of a <connection> block:

bind, connect-retry, connect-retry-max, connect-timeout, explicit-exit-notify, float, fragment, http-proxy, http-proxy-option, link-mtu, local, lport, mssfix, mtu-disc, nobind, port, proto, remote, rport, socks-proxy, tun-mtu and tun-mtu-extra.

A defaulting mechanism exists for specifying options to apply to all <connection> profiles. If any of the above options (with the exception of remote ) appear outside of a <connection> block, but in a configuration file which has one or more <connection> blocks, the option setting will be used as a default for <connection> blocks which follow it in the configuration file.

For example, suppose the nobind option were placed in the sample configuration file above, near the top of the file, before the first <connection> block. The effect would be as if nobind were declared in all <connection> blocks below it.

--proto-force p

When iterating through connection profiles, only consider profiles using protocol p ('tcp'|'udp').

--remote-random

When multiple --remote address/ports are specified, or if connection profiles are being used, initially randomize the order of the list as a kind of basic load-balancing measure.

--proto p

Use protocol p for communicating with remote host. p can be udp, tcp-client, or tcp-server.

The default protocol is udp when --proto is not specified.

For UDP operation, --proto udp should be specified on both peers.

For TCP operation, one peer must use --proto tcp-server and the other must use --proto tcp-client. A peer started with tcp-server will wait indefinitely for an incoming connection. A peer started with tcp-client will attempt to connect, and if that fails, will sleep for 5 seconds (adjustable via the --connect-retry option) and try again infinite or up to N retries (adjustable via the --connect-retry-max option). Both TCP client and server will simulate a SIGUSR1 restart signal if either side resets the connection.

OpenVPN is designed to operate optimally over UDP, but TCP capability is provided for situations where UDP cannot be used. In comparison with UDP, TCP will usually be somewhat less efficient and less robust when used over unreliable or congested networks.

This article outlines some of problems with tunneling IP over TCP:

http://sites.inka.de/sites/bigred/devel/tcp-tcp.html

There are certain cases, however, where using TCP may be advantageous from a security and robustness perspective, such as tunneling non-IP or application-level UDP protocols, or tunneling protocols which don't possess a built-in reliability layer.

--connect-retry n [max]

Wait n seconds between connection attempts (default=5). Repeated reconnection attempts are slowed down after 5 retries per remote by doubling the wait time after each unsuccessful attempt. The optional argument max specifies the maximum value of wait time in seconds at which it gets capped (default=300).

--connect-retry-max n

n specifies the number of times each --remote or <connection> entry is tried. Specifying n as one would try each entry exactly once. A successful connection resets the counter. (default=unlimited).

--show-proxy-settings

Show sensed HTTP or SOCKS proxy settings. Currently, only Windows clients support this option.

--http-proxy server port [authfile|'auto'|'auto-nct'] [auth-method]

Connect to remote host through an HTTP proxy at address server and port port. If HTTP Proxy-Authenticate is required, authfile is a file containing a username and password on 2 lines, or "stdin" to prompt from console. Its content can also be specified in the config file with the --http-proxy-user-pass option. (See section on inline files)

auth-method should be one of "none", "basic", or "ntlm".

HTTP Digest authentication is supported as well, but only via the auto or auto-nct flags (below).

The auto flag causes OpenVPN to automatically determine the auth-method and query stdin or the management interface for username/password credentials, if required. This flag exists on OpenVPN 2.1 or higher.

The auto-nct flag (no clear-text auth) instructs OpenVPN to automatically determine the authentication method, but to reject weak authentication protocols such as HTTP Basic Authentication.

--http-proxy-option type [parm]

Set extended HTTP proxy options. Repeat to set multiple options.

VERSION version -- Set HTTP version number to version (default=1.0).

AGENT user-agent -- Set HTTP "User-Agent" string to user-agent.

CUSTOM-HEADER name content -- Adds the custom Header with name as name and content as the content of the custom HTTP header.

--socks-proxy server [port] [authfile]

Connect to remote host through a Socks5 proxy at address server and port port (default=1080). authfile (optional) is a file containing a username and password on 2 lines, or "stdin" to prompt from console.

--resolv-retry n

If hostname resolve fails for --remote, retry resolve for n seconds before failing.

Set n to "infinite" to retry indefinitely.

By default, --resolv-retry infinite is enabled. You can disable by setting n=0.

--float

Allow remote peer to change its IP address and/or port number, such as due to DHCP (this is the default if --remote is not used). --float when specified with --remote allows an OpenVPN session to initially connect to a peer at a known address, however if packets arrive from a new address and pass all authentication tests, the new address will take control of the session. This is useful when you are connecting to a peer which holds a dynamic address such as a dial-in user or DHCP client.

Essentially, --float tells OpenVPN to accept authenticated packets from any address, not only the address which was specified in the --remote option.

--ipchange cmd

Run command cmd when our remote ip-address is initially authenticated or changes.

cmd consists of a path to script (or executable program), optionally followed by arguments. The path and arguments may be single- or double-quoted and/or escaped using a backslash, and should be separated by one or more spaces.

When cmd is executed two arguments are appended after any arguments specified in cmd , as follows:

cmd ip_address port_number

Don't use --ipchange in --mode server mode. Use a --client-connect script instead.

See the "Environmental Variables" section below for additional parameters passed as environmental variables.

If you are running in a dynamic IP address environment where the IP addresses of either peer could change without notice, you can use this script, for example, to edit the /etc/hosts file with the current address of the peer. The script will be run every time the remote peer changes its IP address.

Similarly if our IP address changes due to DHCP, we should configure our IP address change script (see man page for dhcpcd(8) ) to deliver a SIGHUP or SIGUSR1 signal to OpenVPN. OpenVPN will then reestablish a connection with its most recently authenticated peer on its new IP address.

--port port

TCP/UDP port number or port name for both local and remote (sets both --lport and --rport options to given port). The current default of 1194 represents the official IANA port number assignment for OpenVPN and has been used since version 2.0-beta17. Previous versions used port 5000 as the default.

--lport port

Set local TCP/UDP port number or name. Cannot be used together with --nobind option.

--rport port

Set TCP/UDP port number or name used by the --remote option. The port can also be set directly using the --remote option.

--bind [ipv6only]

Bind to local address and port. This is the default unless any of --proto tcp-client , --http-proxy or --socks-proxy are used.

If the ipv6only keyword is present OpenVPN will bind only to IPv6 (as oposed to IPv6 and IPv4) when a IPv6 socket is opened.

--nobind

Do not bind to local address and port. The IP stack will allocate a dynamic port for returning packets. Since the value of the dynamic port could not be known in advance by a peer, this option is only suitable for peers which will be initiating connections by using the --remote option.

--dev tunX | tapX | null

TUN/TAP virtual network device ( X can be omitted for a dynamic device.)

See examples section below for an example on setting up a TUN device.

You must use either tun devices on both ends of the connection or tap devices on both ends. You cannot mix them, as they represent different underlying network layers.

tun devices encapsulate IPv4 or IPv6 (OSI Layer 3) while tap devices encapsulate Ethernet 802.3 (OSI Layer 2).

--dev-type device-type

Which device type are we using? device-type should be tun (OSI Layer 3) or tap (OSI Layer 2). Use this option only if the TUN/TAP device used with --dev does not begin with tun or tap.

--topology mode

Configure virtual addressing topology when running in --dev tun mode. This directive has no meaning in --dev tap mode, which always uses a subnet topology.

If you set this directive on the server, the --server and --server-bridge directives will automatically push your chosen topology setting to clients as well. This directive can also be manually pushed to clients. Like the --dev directive, this directive must always be compatible between client and server.

mode can be one of:

net30 -- Use a point-to-point topology, by allocating one /30 subnet per client. This is designed to allow point-to-point semantics when some or all of the connecting clients might be Windows systems. This is the default on OpenVPN 2.0.

p2p -- Use a point-to-point topology where the remote endpoint of the client's tun interface always points to the local endpoint of the server's tun interface. This mode allocates a single IP address per connecting client. Only use when none of the connecting clients are Windows systems. This mode is functionally equivalent to the --ifconfig-pool-linear directive which is available in OpenVPN 2.0 and is now deprecated.

subnet -- Use a subnet rather than a point-to-point topology by configuring the tun interface with a local IP address and subnet mask, similar to the topology used in --dev tap and ethernet bridging mode. This mode allocates a single IP address per connecting client and works on Windows as well. Only available when server and clients are OpenVPN 2.1 or higher, or OpenVPN 2.0.x which has been manually patched with the --topology directive code. When used on Windows, requires version 8.2 or higher of the TAP-Win32 driver. When used on *nix, requires that the tun driver supports an ifconfig(8) command which sets a subnet instead of a remote endpoint IP address.

This option exists in OpenVPN 2.1 or higher.

Note: Using --topology subnet changes the interpretation of the arguments of --ifconfig to mean "address netmask", no longer "local remote".

--dev-node node

Explicitly set the device node rather than using /dev/net/tun, /dev/tun, /dev/tap, etc. If OpenVPN cannot figure out whether node is a TUN or TAP device based on the name, you should also specify --dev-type tun or --dev-type tap.

Under Mac OS X this option can be used to specify the default tun implementation. Using --dev-node utun forces usage of the native Darwin tun kernel support. Use --dev-node utunN to select a specific utun instance. To force using the tun.kext (/dev/tunX) use --dev-node tun. When not specifying a --dev-node option openvpn will first try to open utun, and fall back to tun.kext.

On Windows systems, select the TAP-Win32 adapter which is named node in the Network Connections Control Panel or the raw GUID of the adapter enclosed by braces. The --show-adapters option under Windows can also be used to enumerate all available TAP-Win32 adapters and will show both the network connections control panel name and the GUID for each TAP-Win32 adapter.

--lladdr address

Specify the link layer address, more commonly known as the MAC address. Only applied to TAP devices.

--iproute cmd

Set alternate command to execute instead of default iproute2 command. May be used in order to execute OpenVPN in unprivileged environment.

--ifconfig l rn

Set TUN/TAP adapter parameters. l is the IP address of the local VPN endpoint. For TUN devices in point-to-point mode, rn is the IP address of the remote VPN endpoint. For TAP devices, or TUN devices used with --topology subnet, rn is the subnet mask of the virtual network segment which is being created or connected to.

For TUN devices, which facilitate virtual point-to-point IP connections (when used in --topology net30 or p2p mode), the proper usage of --ifconfig is to use two private IP addresses which are not a member of any existing subnet which is in use. The IP addresses may be consecutive and should have their order reversed on the remote peer. After the VPN is established, by pinging rn, you will be pinging across the VPN.

For TAP devices, which provide the ability to create virtual ethernet segments, or TUN devices in --topology subnet mode (which create virtual "multipoint networks"), --ifconfig is used to set an IP address and subnet mask just as a physical ethernet adapter would be similarly configured. If you are attempting to connect to a remote ethernet bridge, the IP address and subnet should be set to values which would be valid on the the bridged ethernet segment (note also that DHCP can be used for the same purpose).

This option, while primarily a proxy for the ifconfig(8) command, is designed to simplify TUN/TAP tunnel configuration by providing a standard interface to the different ifconfig implementations on different platforms.

--ifconfig parameters which are IP addresses can also be specified as a DNS or /etc/hosts file resolvable name.

For TAP devices, --ifconfig should not be used if the TAP interface will be getting an IP address lease from a DHCP server.

--ifconfig-noexec

Don't actually execute ifconfig/netsh commands, instead pass --ifconfig parameters to scripts using environmental variables.

--ifconfig-nowarn

Don't output an options consistency check warning if the --ifconfig option on this side of the connection doesn't match the remote side. This is useful when you want to retain the overall benefits of the options consistency check (also see --disable-occ option) while only disabling the ifconfig component of the check.

For example, if you have a configuration where the local host uses --ifconfig but the remote host does not, use --ifconfig-nowarn on the local host.

This option will also silence warnings about potential address conflicts which occasionally annoy more experienced users by triggering "false positive" warnings.

--route network/IP [netmask] [gateway] [metric]

Add route to routing table after connection is established. Multiple routes can be specified. Routes will be automatically torn down in reverse order prior to TUN/TAP device close.

This option is intended as a convenience proxy for the route(8) shell command, while at the same time providing portable semantics across OpenVPN's platform space.

netmask default -- 255.255.255.255

gateway default -- taken from --route-gateway or the second parameter to --ifconfig when --dev tun is specified.

metric default -- taken from --route-metric otherwise 0.

The default can be specified by leaving an option blank or setting it to "default".

The network and gateway parameters can also be specified as a DNS or /etc/hosts file resolvable name, or as one of three special keywords:

vpn_gateway -- The remote VPN endpoint address (derived either from --route-gateway or the second parameter to --ifconfig when --dev tun is specified).

net_gateway -- The pre-existing IP default gateway, read from the routing table (not supported on all OSes).

remote_host -- The --remote address if OpenVPN is being run in client mode, and is undefined in server mode.

--route-gateway gw|'dhcp'

Specify a default gateway gw for use with --route.

If dhcp is specified as the parameter, the gateway address will be extracted from a DHCP negotiation with the OpenVPN server-side LAN.

--route-metric m

Specify a default metric m for use with --route.

--route-delay [n] [w]

Delay n seconds (default=0) after connection establishment, before adding routes. If n is 0, routes will be added immediately upon connection establishment. If --route-delay is omitted, routes will be added immediately after TUN/TAP device open and --up script execution, before any --user or --group privilege downgrade (or --chroot execution.)

This option is designed to be useful in scenarios where DHCP is used to set tap adapter addresses. The delay will give the DHCP handshake time to complete before routes are added.

On Windows, --route-delay tries to be more intelligent by waiting w seconds (w=30 by default) for the TAP-Win32 adapter to come up before adding routes.

--route-up cmd

Run command cmd after routes are added, subject to --route-delay.

See the "Environmental Variables" section below for additional parameters passed as environmental variables.

--route-pre-down cmd

Run command cmd before routes are removed upon disconnection.

See the "Environmental Variables" section below for additional parameters passed as environmental variables.

--route-noexec

Don't add or remove routes automatically. Instead pass routes to --route-up script using environmental variables.

--route-nopull

When used with --client or --pull, accept options pushed by server EXCEPT for routes, block-outside-dns and dhcp options like DNS servers.

When used on the client, this option effectively bars the server from adding routes to the client's routing table, however note that this option still allows the server to set the TCP/IP properties of the client's TUN/TAP interface.

--allow-pull-fqdn

Allow client to pull DNS names from server (rather than being limited to IP address) for --ifconfig, --route, and --route-gateway.

--client-nat snat|dnat network netmask alias

This pushable client option sets up a stateless one-to-one NAT rule on packet addresses (not ports), and is useful in cases where routes or ifconfig settings pushed to the client would create an IP numbering conflict.

network/netmask (for example 192.168.0.0/255.255.0.0) defines the local view of a resource from the client perspective, while alias/netmask (for example 10.64.0.0/255.255.0.0) defines the remote view from the server perspective.

Use snat (source NAT) for resources owned by the client and dnat (destination NAT) for remote resources.

Set --verb 6 for debugging info showing the transformation of src/dest addresses in packets.

--redirect-gateway flags...

Automatically execute routing commands to cause all outgoing IP traffic to be redirected over the VPN. This is a client-side option.

This option performs three steps:

(1) Create a static route for the --remote address which forwards to the pre-existing default gateway. This is done so that (3) will not create a routing loop.

(2) Delete the default gateway route.

(3) Set the new default gateway to be the VPN endpoint address (derived either from --route-gateway or the second parameter to --ifconfig when --dev tun is specified).

When the tunnel is torn down, all of the above steps are reversed so that the original default route is restored.

Option flags:

local -- Add the local flag if both OpenVPN servers are directly connected via a common subnet, such as with wireless. The local flag will cause step 1 above to be omitted.

autolocal -- Try to automatically determine whether to enable local flag above.

def1 -- Use this flag to override the default gateway by using 0.0.0.0/1 and 128.0.0.0/1 rather than 0.0.0.0/0. This has the benefit of overriding but not wiping out the original default gateway.

bypass-dhcp -- Add a direct route to the DHCP server (if it is non-local) which bypasses the tunnel (Available on Windows clients, may not be available on non-Windows clients).

bypass-dns -- Add a direct route to the DNS server(s) (if they are non-local) which bypasses the tunnel (Available on Windows clients, may not be available on non-Windows clients).

block-local -- Block access to local LAN when the tunnel is active, except for the LAN gateway itself. This is accomplished by routing the local LAN (except for the LAN gateway address) into the tunnel.

ipv6 -- Redirect IPv6 routing into the tunnel. This works similar to the def1 flag, that is, more specific IPv6 routes are added (2000::/4, 3000::/4), covering the whole IPv6 unicast space.

!ipv4 -- Do not redirect IPv4 traffic - typically used in the flag pair ipv6 !ipv4 to redirect IPv6-only.

--link-mtu n

Sets an upper bound on the size of UDP packets which are sent between OpenVPN peers. It's best not to set this parameter unless you know what you're doing.

--redirect-private [flags]

Like --redirect-gateway, but omit actually changing the default gateway. Useful when pushing private subnets.

--tun-mtu n

Take the TUN device MTU to be n and derive the link MTU from it (default=1500). In most cases, you will probably want to leave this parameter set to its default value.

The MTU (Maximum Transmission Units) is the maximum datagram size in bytes that can be sent unfragmented over a particular network path. OpenVPN requires that packets on the control or data channels be sent unfragmented.

MTU problems often manifest themselves as connections which hang during periods of active usage.

It's best to use the --fragment and/or --mssfix options to deal with MTU sizing issues.

--tun-mtu-extra n

Assume that the TUN/TAP device might return as many as n bytes more than the --tun-mtu size on read. This parameter defaults to 0, which is sufficient for most TUN devices. TAP devices may introduce additional overhead in excess of the MTU size, and a setting of 32 is the default when TAP devices are used. This parameter only controls internal OpenVPN buffer sizing, so there is no transmission overhead associated with using a larger value.

--mtu-disc type

Should we do Path MTU discovery on TCP/UDP channel? Only supported on OSes such as Linux that supports the necessary system call to set.

'no' -- Never send DF (Don't Fragment) frames
'maybe' -- Use per-route hints
'yes' -- Always DF (Don't Fragment)

--mtu-test

To empirically measure MTU on connection startup, add the --mtu-test option to your configuration. OpenVPN will send ping packets of various sizes to the remote peer and measure the largest packets which were successfully received. The --mtu-test process normally takes about 3 minutes to complete.

--fragment max

Enable internal datagram fragmentation so that no UDP datagrams are sent which are larger than max bytes.

The max parameter is interpreted in the same way as the --link-mtu parameter, i.e. the UDP packet size after encapsulation overhead has been added in, but not including the UDP header itself.

The --fragment option only makes sense when you are using the UDP protocol ( --proto udp ).

--fragment adds 4 bytes of overhead per datagram.

See the --mssfix option below for an important related option to --fragment.

It should also be noted that this option is not meant to replace UDP fragmentation at the IP stack level. It is only meant as a last resort when path MTU discovery is broken. Using this option is less efficient than fixing path MTU discovery for your IP link and using native IP fragmentation instead.

Having said that, there are circumstances where using OpenVPN's internal fragmentation capability may be your only option, such as tunneling a UDP multicast stream which requires fragmentation.

--mssfix max

Announce to TCP sessions running over the tunnel that they should limit their send packet sizes such that after OpenVPN has encapsulated them, the resulting UDP packet size that OpenVPN sends to its peer will not exceed max bytes. The default value is 1450.

The max parameter is interpreted in the same way as the --link-mtu parameter, i.e. the UDP packet size after encapsulation overhead has been added in, but not including the UDP header itself. Resulting packet would be at most 28 bytes larger for IPv4 and 48 bytes for IPv6 (20/40 bytes for IP header and 8 bytes for UDP header). Default value of 1450 allows IPv4 packets to be transmitted over a link with MTU 1473 or higher without IP level fragmentation.

The --mssfix option only makes sense when you are using the UDP protocol for OpenVPN peer-to-peer communication, i.e. --proto udp.

--mssfix and --fragment can be ideally used together, where --mssfix will try to keep TCP from needing packet fragmentation in the first place, and if big packets come through anyhow (from protocols other than TCP), --fragment will internally fragment them.

Both --fragment and --mssfix are designed to work around cases where Path MTU discovery is broken on the network path between OpenVPN peers.

The usual symptom of such a breakdown is an OpenVPN connection which successfully starts, but then stalls during active usage.

If --fragment and --mssfix are used together, --mssfix will take its default max parameter from the --fragment max option.

Therefore, one could lower the maximum UDP packet size to 1300 (a good first try for solving MTU-related connection problems) with the following options:

--tun-mtu 1500 --fragment 1300 --mssfix

--sndbuf size

Set the TCP/UDP socket send buffer size. Defaults to operation system default.

--rcvbuf size

Set the TCP/UDP socket receive buffer size. Defaults to operation system default.

--mark value

Mark encrypted packets being sent with value. The mark value can be matched in policy routing and packetfilter rules. This option is only supported in Linux and does nothing on other operating systems.

--socket-flags flags...

Apply the given flags to the OpenVPN transport socket. Currently, only TCP_NODELAY is supported.

The TCP_NODELAY socket flag is useful in TCP mode, and causes the kernel to send tunnel packets immediately over the TCP connection without trying to group several smaller packets into a larger packet. This can result in a considerably improvement in latency.

This option is pushable from server to client, and should be used on both client and server for maximum effect.

--txqueuelen n

(Linux only) Set the TX queue length on the TUN/TAP interface. Currently defaults to 100.

--shaper n

Limit bandwidth of outgoing tunnel data to n bytes per second on the TCP/UDP port. Note that this will only work if mode is set to p2p. If you want to limit the bandwidth in both directions, use this option on both peers.

OpenVPN uses the following algorithm to implement traffic shaping: Given a shaper rate of n bytes per second, after a datagram write of b bytes is queued on the TCP/UDP port, wait a minimum of (b / n) seconds before queuing the next write.

It should be noted that OpenVPN supports multiple tunnels between the same two peers, allowing you to construct full-speed and reduced bandwidth tunnels at the same time, routing low-priority data such as off-site backups over the reduced bandwidth tunnel, and other data over the full-speed tunnel.

Also note that for low bandwidth tunnels (under 1000 bytes per second), you should probably use lower MTU values as well (see above), otherwise the packet latency will grow so large as to trigger timeouts in the TLS layer and TCP connections running over the tunnel.

OpenVPN allows n to be between 100 bytes/sec and 100 Mbytes/sec.

--inactive n [bytes]

Causes OpenVPN to exit after n seconds of inactivity on the TUN/TAP device. The time length of inactivity is measured since the last incoming or outgoing tunnel packet. The default value is 0 seconds, which disables this feature.

If the optional bytes parameter is included, exit if less than bytes of combined in/out traffic are produced on the tun/tap device in n seconds.

In any case, OpenVPN's internal ping packets (which are just keepalives) and TLS control packets are not considered "activity", nor are they counted as traffic, as they are used internally by OpenVPN and are not an indication of actual user activity.

--ping n

Ping remote over the TCP/UDP control channel if no packets have been sent for at least n seconds (specify --ping on both peers to cause ping packets to be sent in both directions since OpenVPN ping packets are not echoed like IP ping packets). When used in one of OpenVPN's secure modes (where --secret, --tls-server, or --tls-client is specified), the ping packet will be cryptographically secure.

This option has two intended uses:

(1) Compatibility with stateful firewalls. The periodic ping will ensure that a stateful firewall rule which allows OpenVPN UDP packets to pass will not time out.

(2) To provide a basis for the remote to test the existence of its peer using the --ping-exit option.

--ping-exit n

Causes OpenVPN to exit after n seconds pass without reception of a ping or other packet from remote. This option can be combined with --inactive, --ping, and --ping-exit to create a two-tiered inactivity disconnect.

For example,

openvpn [options...] --inactive 3600 --ping 10 --ping-exit 60

when used on both peers will cause OpenVPN to exit within 60 seconds if its peer disconnects, but will exit after one hour if no actual tunnel data is exchanged.

--ping-restart n

Similar to --ping-exit, but trigger a SIGUSR1 restart after n seconds pass without reception of a ping or other packet from remote.

This option is useful in cases where the remote peer has a dynamic IP address and a low-TTL DNS name is used to track the IP address using a service such as http://dyndns.org/ + a dynamic DNS client such as ddclient.

If the peer cannot be reached, a restart will be triggered, causing the hostname used with --remote to be re-resolved (if --resolv-retry is also specified).

In server mode, --ping-restart, --inactive, or any other type of internally generated signal will always be applied to individual client instance objects, never to whole server itself. Note also in server mode that any internally generated signal which would normally cause a restart, will cause the deletion of the client instance object instead.

In client mode, the --ping-restart parameter is set to 120 seconds by default. This default will hold until the client pulls a replacement value from the server, based on the --keepalive setting in the server configuration. To disable the 120 second default, set --ping-restart 0 on the client.

See the signals section below for more information on SIGUSR1.

Note that the behavior of SIGUSR1 can be modified by the --persist-tun, --persist-key, --persist-local-ip, and --persist-remote-ip options.

Also note that --ping-exit and --ping-restart are mutually exclusive and cannot be used together.

--keepalive interval timeout

A helper directive designed to simplify the expression of --ping and --ping-restart.

This option can be used on both client and server side, but it is in enough to add this on the server side as it will push appropriate --ping and --ping-restart options to the client. If used on both server and client, the values pushed from server will override the client local values.

The timeout argument will be twice as long on the server side. This ensures that a timeout is detected on client side before the server side drops the connection.

For example, --keepalive 10 60 expands as follows:

 if mode server:
   ping 10                    # Argument: interval
   ping-restart 120           # Argument: timeout*2
   push "ping 10"             # Argument: interval
   push "ping-restart 60"     # Argument: timeout
 else
   ping 10                    # Argument: interval
   ping-restart 60            # Argument: timeout

--ping-timer-rem

Run the --ping-exit / --ping-restart timer only if we have a remote address. Use this option if you are starting the daemon in listen mode (i.e. without an explicit --remote peer), and you don't want to start clocking timeouts until a remote peer connects.

--persist-tun

Don't close and reopen TUN/TAP device or run up/down scripts across SIGUSR1 or --ping-restart restarts.

SIGUSR1 is a restart signal similar to SIGHUP, but which offers finer-grained control over reset options.

--persist-key

Don't re-read key files across SIGUSR1 or --ping-restart.

This option can be combined with --user nobody to allow restarts triggered by the SIGUSR1 signal. Normally if you drop root privileges in OpenVPN, the daemon cannot be restarted since it will now be unable to re-read protected key files.

This option solves the problem by persisting keys across SIGUSR1 resets, so they don't need to be re-read.

--persist-local-ip

Preserve initially resolved local IP address and port number across SIGUSR1 or --ping-restart restarts.

--persist-remote-ip

Preserve most recently authenticated remote IP address and port number across SIGUSR1 or --ping-restart restarts.

--mlock

Disable paging by calling the POSIX mlockall function. Requires that OpenVPN be initially run as root (though OpenVPN can subsequently downgrade its UID using the --user option).

Using this option ensures that key material and tunnel data are never written to disk due to virtual memory paging operations which occur under most modern operating systems. It ensures that even if an attacker was able to crack the box running OpenVPN, he would not be able to scan the system swap file to recover previously used ephemeral keys, which are used for a period of time governed by the --reneg options (see below), then are discarded.

The downside of using --mlock is that it will reduce the amount of physical memory available to other applications.

--up cmd

Run command cmd after successful TUN/TAP device open (pre --user UID change).

The up command is useful for specifying route commands which route IP traffic destined for private subnets which exist at the other end of the VPN connection into the tunnel.

For --dev tun execute as:

cmd tun_dev tun_mtu link_mtu ifconfig_local_ip ifconfig_remote_ip [ init | restart ]

For --dev tap execute as:

cmd tap_dev tap_mtu link_mtu ifconfig_local_ip ifconfig_netmask [ init | restart ]

See the "Environmental Variables" section below for additional parameters passed as environmental variables.

Note that if cmd includes arguments, all OpenVPN-generated arguments will be appended to them to build an argument list with which the executable will be called.

Typically, cmd will run a script to add routes to the tunnel.

Normally the up script is called after the TUN/TAP device is opened. In this context, the last command line parameter passed to the script will be init. If the --up-restart option is also used, the up script will be called for restarts as well. A restart is considered to be a partial reinitialization of OpenVPN where the TUN/TAP instance is preserved (the --persist-tun option will enable such preservation). A restart can be generated by a SIGUSR1 signal, a --ping-restart timeout, or a connection reset when the TCP protocol is enabled with the --proto option. If a restart occurs, and --up-restart has been specified, the up script will be called with restart as the last parameter.

NOTE: on restart, OpenVPN will not pass the full set of environment variables to the script. Namely, everything related to routing and gateways will not be passed, as nothing needs to be done anyway - all the routing setup is already in place. Additionally, the up-restart script will run with the downgraded UID/GID settings (if configured).

The following standalone example shows how the --up script can be called in both an initialization and restart context. (NOTE: for security reasons, don't run the following example unless UDP port 9999 is blocked by your firewall. Also, the example will run indefinitely, so you should abort with control-c).

openvpn --dev tun --port 9999 --verb 4 --ping-restart 10 --up 'echo up' --down 'echo down' --persist-tun --up-restart

Note that OpenVPN also provides the --ifconfig option to automatically ifconfig the TUN device, eliminating the need to define an --up script, unless you also want to configure routes in the --up script.

If --ifconfig is also specified, OpenVPN will pass the ifconfig local and remote endpoints on the command line to the --up script so that they can be used to configure routes such as:

route add -net 10.0.0.0 netmask 255.255.255.0 gw $5

--up-delay

Delay TUN/TAP open and possible --up script execution until after TCP/UDP connection establishment with peer.

In --proto udp mode, this option normally requires the use of --ping to allow connection initiation to be sensed in the absence of tunnel data, since UDP is a "connectionless" protocol.

On Windows, this option will delay the TAP-Win32 media state transitioning to "connected" until connection establishment, i.e. the receipt of the first authenticated packet from the peer.

--down cmd

Run command cmd after TUN/TAP device close (post --user UID change and/or --chroot ). cmd consists of a path to script (or executable program), optionally followed by arguments. The path and arguments may be single- or double-quoted and/or escaped using a backslash, and should be separated by one or more spaces.

Called with the same parameters and environmental variables as the --up option above.

Note that if you reduce privileges by using --user and/or --group, your --down script will also run at reduced privilege.

--down-pre

Call --down cmd/script before, rather than after, TUN/TAP close.

--up-restart

Enable the --up and --down scripts to be called for restarts as well as initial program start. This option is described more fully above in the --up option documentation.

--setenv name value

Set a custom environmental variable name=value to pass to script.

--setenv FORWARD_COMPATIBLE 1

Relax config file syntax checking so that unknown directives will trigger a warning but not a fatal error, on the assumption that a given unknown directive might be valid in future OpenVPN versions.

This option should be used with caution, as there are good security reasons for having OpenVPN fail if it detects problems in a config file. Having said that, there are valid reasons for wanting new software features to gracefully degrade when encountered by older software versions.

It is also possible to tag a single directive so as not to trigger a fatal error if the directive isn't recognized. To do this, prepend the following before the directive: setenv opt

Versions prior to OpenVPN 2.3.3 will always ignore options set with the setenv opt directive.

Server Mode

Starting with OpenVPN 2.0, a multi-client TCP/UDP server mode is supported, and can be enabled with the --mode server option. In server mode, OpenVPN will listen on a single port for incoming client connections. All client connections will be routed through a single tun or tap interface. This mode is designed for scalability and should be able to support hundreds or even thousands of clients on sufficiently fast hardware. SSL/TLS authentication must be used in this mode.

--server network netmask ['nopool']

A helper directive designed to simplify the configuration of OpenVPN's server mode. This directive will set up an OpenVPN server which will allocate addresses to clients out of the given network/netmask. The server itself will take the ".1" address of the given network for use as the server-side endpoint of the local TUN/TAP interface.

For example, --server 10.8.0.0 255.255.255.0 expands as follows:

 mode server
 tls-server
 push "topology [topology]"

 if dev tun AND (topology == net30 OR topology == p2p):
   ifconfig 10.8.0.1 10.8.0.2
   if !nopool:
     ifconfig-pool 10.8.0.4 10.8.0.251
   route 10.8.0.0 255.255.255.0
   if client-to-client:
     push "route 10.8.0.0 255.255.255.0"
   else if topology == net30:
     push "route 10.8.0.1"

 if dev tap OR (dev tun AND topology == subnet):
   ifconfig 10.8.0.1 255.255.255.0
   if !nopool:
     ifconfig-pool 10.8.0.2 10.8.0.253 255.255.255.0
   push "route-gateway 10.8.0.1"
   if route-gateway unset:
     route-gateway 10.8.0.2

Don't use --server if you are ethernet bridging. Use --server-bridge instead.

--server-bridge gateway netmask pool-start-IP pool-end-IP

--server-bridge ['nogw']

A helper directive similar to --server which is designed to simplify the configuration of OpenVPN's server mode in ethernet bridging configurations.

If --server-bridge is used without any parameters, it will enable a DHCP-proxy mode, where connecting OpenVPN clients will receive an IP address for their TAP adapter from the DHCP server running on the OpenVPN server-side LAN. Note that only clients that support the binding of a DHCP client with the TAP adapter (such as Windows) can support this mode. The optional nogw flag (advanced) indicates that gateway information should not be pushed to the client.

To configure ethernet bridging, you must first use your OS's bridging capability to bridge the TAP interface with the ethernet NIC interface. For example, on Linux this is done with the brctl tool, and with Windows XP it is done in the Network Connections Panel by selecting the ethernet and TAP adapters and right-clicking on "Bridge Connections".

Next you you must manually set the IP/netmask on the bridge interface. The gateway and netmask parameters to --server-bridge can be set to either the IP/netmask of the bridge interface, or the IP/netmask of the default gateway/router on the bridged subnet.

Finally, set aside a IP range in the bridged subnet, denoted by pool-start-IP and pool-end-IP, for OpenVPN to allocate to connecting clients.

For example, server-bridge 10.8.0.4 255.255.255.0 10.8.0.128 10.8.0.254 expands as follows:

mode server
tls-server

ifconfig-pool 10.8.0.128 10.8.0.254 255.255.255.0
push "route-gateway 10.8.0.4"

In another example, --server-bridge (without parameters) expands as follows:

mode server
tls-server

push "route-gateway dhcp"

Or --server-bridge nogw expands as follows:

mode server
tls-server

--push option

Push a config file option back to the client for remote execution. Note that option must be enclosed in double quotes (""). The client must specify --pull in its config file. The set of options which can be pushed is limited by both feasibility and security. Some options such as those which would execute scripts are banned, since they would effectively allow a compromised server to execute arbitrary code on the client. Other options such as TLS or MTU parameters cannot be pushed because the client needs to know them before the connection to the server can be initiated.

This is a partial list of options which can currently be pushed: --route, --route-gateway, --route-delay, --redirect-gateway, --ip-win32, --dhcp-option, --inactive, --ping, --ping-exit, --ping-restart, --setenv, --auth-token, --persist-key, --persist-tun, --echo, --comp-lzo, --socket-flags, --sndbuf, --rcvbuf

--push-reset

Don't inherit the global push list for a specific client instance. Specify this option in a client-specific context such as with a --client-config-dir configuration file. This option will ignore --push options at the global config file level.

--push-remove opt

selectively remove all --push options matching "opt" from the option list for a client. "opt" is matched as a substring against the whole option string to-be-pushed to the client, so --push-remove route would remove all --push route ... and --push route-ipv6 ... statements, while --push-remove 'route-ipv6 2001:' would only remove IPv6 routes for 2001:... networks.

--push-remove can only be used in a client-specific context, like in a --client-config-dir file, or --client-connect script or plugin -- similar to --push-reset, just more selective.

NOTE: to change an option, --push-remove can be used to first remove the old value, and then add a new --push option with the new value.

--push-peer-info

Push additional information about the client to server. The following data is always pushed to the server:

IV_VER=<version> -- the client OpenVPN version

IV_LZO_STUB=1 -- if client was built with LZO stub capability

IV_LZ4=1 -- if the client supports LZ4 compressions.

IV_PROTO=2 -- if the client supports peer-id floating mechansim

IV_NCP=2 -- negotiable ciphers, client supports --cipher pushed by the server, a value of 2 or greater indicates client supports AES-GCM-128 and AES-GCM-256.

IV_UI_VER=<gui_id> <version> -- the UI version of a UI if one is running, for example "de.blinkt.openvpn 0.5.47" for the Android app.

When --push-peer-info is enabled the additional information consists of the following data:

IV_HWADDR=<mac address> -- the MAC address of clients default gateway

IV_SSL=<version string> -- the ssl version used by the client, e.g. "OpenSSL 1.0.2f 28 Jan 2016".

IV_PLAT_VER=x.y - the version of the operating system, e.g. 6.1 for Windows 7.

UV_<name>=<value> -- client environment variables whose names start with "UV_"

--disable

Disable a particular client (based on the common name) from connecting. Don't use this option to disable a client due to key or password compromise. Use a CRL (certificate revocation list) instead (see the --crl-verify option).

This option must be associated with a specific client instance, which means that it must be specified either in a client instance config file using --client-config-dir or dynamically generated using a --client-connect script.

--ifconfig-pool start-IP end-IP [netmask]

Set aside a pool of subnets to be dynamically allocated to connecting clients, similar to a DHCP server. For tun-style tunnels, each client will be given a /30 subnet (for interoperability with Windows clients). For tap-style tunnels, individual addresses will be allocated, and the optional netmask parameter will also be pushed to clients.

--ifconfig-pool-persist file [seconds]

Persist/unpersist ifconfig-pool data to file, at seconds intervals (default=600), as well as on program startup and shutdown.

The goal of this option is to provide a long-term association between clients (denoted by their common name) and the virtual IP address assigned to them from the ifconfig-pool. Maintaining a long-term association is good for clients because it allows them to effectively use the --persist-tun option.

file is a comma-delimited ASCII file, formatted as <Common-Name>,<IP-address>.

If seconds = 0, file will be treated as read-only. This is useful if you would like to treat file as a configuration file.

Note that the entries in this file are treated by OpenVPN as suggestions only, based on past associations between a common name and IP address. They do not guarantee that the given common name will always receive the given IP address. If you want guaranteed assignment, use --ifconfig-push

--ifconfig-pool-linear

Modifies the --ifconfig-pool directive to allocate individual TUN interface addresses for clients rather than /30 subnets. NOTE: This option is incompatible with Windows clients.

This option is deprecated, and should be replaced with --topology p2p which is functionally equivalent.

--ifconfig-push local remote-netmask [alias]

Push virtual IP endpoints for client tunnel, overriding the --ifconfig-pool dynamic allocation.

The parameters local and remote-netmask are set according to the --ifconfig directive which you want to execute on the client machine to configure the remote end of the tunnel. Note that the parameters local and remote-netmask are from the perspective of the client, not the server. They may be DNS names rather than IP addresses, in which case they will be resolved on the server at the time of client connection.

The optional alias parameter may be used in cases where NAT causes the client view of its local endpoint to differ from the server view. In this case local/remote-netmask will refer to the server view while alias/remote-netmask will refer to the client view.

Remember also to include a --route directive in the main OpenVPN config file which encloses local, so that the kernel will know to route it to the server's TUN/TAP interface.

OpenVPN's internal client IP address selection algorithm works as follows:

1 -- Use --client-connect script generated file for static IP (first choice).
2 -- Use --client-config-dir file for static IP (next choice).
3 -- Use --ifconfig-pool allocation for dynamic IP (last choice).

--iroute network [netmask]

Generate an internal route to a specific client. The netmask parameter, if omitted, defaults to 255.255.255.255.

This directive can be used to route a fixed subnet from the server to a particular client, regardless of where the client is connecting from. Remember that you must also add the route to the system routing table as well (such as by using the --route directive). The reason why two routes are needed is that the --route directive routes the packet from the kernel to OpenVPN. Once in OpenVPN, the --iroute directive routes to the specific client.

This option must be specified either in a client instance config file using --client-config-dir or dynamically generated using a --client-connect script.

The --iroute directive also has an important interaction with --push "route ...". --iroute essentially defines a subnet which is owned by a particular client (we will call this client A). If you would like other clients to be able to reach A's subnet, you can use --push "route ..." together with --client-to-client to effect this. In order for all clients to see A's subnet, OpenVPN must push this route to all clients EXCEPT for A, since the subnet is already owned by A. OpenVPN accomplishes this by not not pushing a route to a client if it matches one of the client's iroutes.

--client-to-client

Because the OpenVPN server mode handles multiple clients through a single tun or tap interface, it is effectively a router. The --client-to-client flag tells OpenVPN to internally route client-to-client traffic rather than pushing all client-originating traffic to the TUN/TAP interface.

When this option is used, each client will "see" the other clients which are currently connected. Otherwise, each client will only see the server. Don't use this option if you want to firewall tunnel traffic using custom, per-client rules.

--duplicate-cn

Allow multiple clients with the same common name to concurrently connect. In the absence of this option, OpenVPN will disconnect a client instance upon connection of a new client having the same common name.

--client-connect cmd

Run command cmd on client connection.

The command is passed the common name and IP address of the just-authenticated client as environmental variables (see environmental variable section below). The command is also passed the pathname of a freshly created temporary file as the last argument (after any arguments specified in cmd ), to be used by the command to pass dynamically generated config file directives back to OpenVPN.

If the script wants to generate a dynamic config file to be applied on the server when the client connects, it should write it to the file named by the last argument.

See the --client-config-dir option below for options which can be legally used in a dynamically generated config file.

Note that the return value of script is significant. If script returns a non-zero error status, it will cause the client to be disconnected.

--client-disconnect cmd

Like --client-connect but called on client instance shutdown. Will not be called unless the --client-connect script and plugins (if defined) were previously called on this instance with successful (0) status returns.

The exception to this rule is if the --client-disconnect command or plugins are cascaded, and at least one client-connect function succeeded, then ALL of the client-disconnect functions for scripts and plugins will be called on client instance object deletion, even in cases where some of the related client-connect functions returned an error status.

The --client-disconnect command is passed the same pathname as the corresponding --client-connect command as its last argument. (after any arguments specified in cmd ).

--client-config-dir dir

Specify a directory dir for custom client config files. After a connecting client has been authenticated, OpenVPN will look in this directory for a file having the same name as the client's X509 common name. If a matching file exists, it will be opened and parsed for client-specific configuration options. If no matching file is found, OpenVPN will instead try to open and parse a default file called "DEFAULT", which may be provided but is not required. Note that the configuration files must be readable by the OpenVPN process after it has dropped it's root privileges.

This file can specify a fixed IP address for a given client using --ifconfig-push, as well as fixed subnets owned by the client using --iroute.

One of the useful properties of this option is that it allows client configuration files to be conveniently created, edited, or removed while the server is live, without needing to restart the server.

The following options are legal in a client-specific context: --push, --push-reset, --push-remove, --iroute, --ifconfig-push, and --config.

--ccd-exclusive

Require, as a condition of authentication, that a connecting client has a --client-config-dir file.

--tmp-dir dir

Specify a directory dir for temporary files. This directory will be used by openvpn processes and script to communicate temporary data with openvpn main process. Note that the directory must be writable by the OpenVPN process after it has dropped it's root privileges.

This directory will be used by in the following cases:

* --client-connect scripts to dynamically generate client-specific configuration files.

* OPENVPN_PLUGIN_AUTH_USER_PASS_VERIFY plugin hook to return success/failure via auth_control_file when using deferred auth method

* OPENVPN_PLUGIN_ENABLE_PF plugin hook to pass filtering rules via pf_file

--hash-size r v

Set the size of the real address hash table to r and the virtual address table to v. By default, both tables are sized at 256 buckets.

--bcast-buffers n

Allocate n buffers for broadcast datagrams (default=256).

--tcp-queue-limit n

Maximum number of output packets queued before TCP (default=64).

When OpenVPN is tunneling data from a TUN/TAP device to a remote client over a TCP connection, it is possible that the TUN/TAP device might produce data at a faster rate than the TCP connection can support. When the number of output packets queued before sending to the TCP socket reaches this limit for a given client connection, OpenVPN will start to drop outgoing packets directed at this client.

--tcp-nodelay

This macro sets the TCP_NODELAY socket flag on the server as well as pushes it to connecting clients. The TCP_NODELAY flag disables the Nagle algorithm on TCP sockets causing packets to be transmitted immediately with low latency, rather than waiting a short period of time in order to aggregate several packets into a larger containing packet. In VPN applications over TCP, TCP_NODELAY is generally a good latency optimization.

The macro expands as follows:

 if mode server:
   socket-flags TCP_NODELAY
   push "socket-flags TCP_NODELAY"

--max-clients n

Limit server to a maximum of n concurrent clients.

--max-routes-per-client n

Allow a maximum of n internal routes per client (default=256). This is designed to help contain DoS attacks where an authenticated client floods the server with packets appearing to come from many unique MAC addresses, forcing the server to deplete virtual memory as its internal routing table expands. This directive can be used in a --client-config-dir file or auto-generated by a --client-connect script to override the global value for a particular client.

Note that this directive affects OpenVPN's internal routing table, not the kernel routing table.

--stale-routes-check n [t]

Remove routes haven't had activity for n seconds (i.e. the ageing time).

This check is ran every t seconds (i.e. check interval).

If t is not present it defaults to n

This option helps to keep the dynamic routing table small. See also --max-routes-per-client

--connect-freq n sec

Allow a maximum of n new connections per sec seconds from clients. This is designed to contain DoS attacks which flood the server with connection requests using certificates which will ultimately fail to authenticate.

This is an imperfect solution however, because in a real DoS scenario, legitimate connections might also be refused.

For the best protection against DoS attacks in server mode, use --proto udp and either --tls-auth or --tls-crypt.

--learn-address cmd

Run command cmd to validate client virtual addresses or routes.

Three arguments will be appended to any arguments in cmd as follows:

[1] operation -- "add", "update", or "delete" based on whether or not the address is being added to, modified, or deleted from OpenVPN's internal routing table.
[2] address -- The address being learned or unlearned. This can be an IPv4 address such as "198.162.10.14", an IPv4 subnet such as "198.162.10.0/24", or an ethernet MAC address (when --dev tap is being used) such as "00:FF:01:02:03:04".
[3] common name -- The common name on the certificate associated with the client linked to this address. Only present for "add" or "update" operations, not "delete".

On "add" or "update" methods, if the script returns a failure code (non-zero), OpenVPN will reject the address and will not modify its internal routing table.

Normally, the cmd script will use the information provided above to set appropriate firewall entries on the VPN TUN/TAP interface. Since OpenVPN provides the association between virtual IP or MAC address and the client's authenticated common name, it allows a user-defined script to configure firewall access policies with regard to the client's high-level common name, rather than the low level client virtual addresses.

--auth-user-pass-verify cmd method

Require the client to provide a username/password (possibly in addition to a client certificate) for authentication.

OpenVPN will run command cmd to validate the username/password provided by the client.

If method is set to "via-env", OpenVPN will call script with the environmental variables username and password set to the username/password strings provided by the client. Be aware that this method is insecure on some platforms which make the environment of a process publicly visible to other unprivileged processes.

If method is set to "via-file", OpenVPN will write the username and password to the first two lines of a temporary file. The filename will be passed as an argument to script, and the file will be automatically deleted by OpenVPN after the script returns. The location of the temporary file is controlled by the --tmp-dir option, and will default to the current directory if unspecified. For security, consider setting --tmp-dir to a volatile storage medium such as /dev/shm (if available) to prevent the username/password file from touching the hard drive.

The script should examine the username and password, returning a success exit code (0) if the client's authentication request is to be accepted, or a failure code (1) to reject the client.

This directive is designed to enable a plugin-style interface for extending OpenVPN's authentication capabilities.

To protect against a client passing a maliciously formed username or password string, the username string must consist only of these characters: alphanumeric, underbar ('_'), dash ('-'), dot ('.'), or at ('@'). The password string can consist of any printable characters except for CR or LF. Any illegal characters in either the username or password string will be converted to underbar ('_').

Care must be taken by any user-defined scripts to avoid creating a security vulnerability in the way that these strings are handled. Never use these strings in such a way that they might be escaped or evaluated by a shell interpreter.

For a sample script that performs PAM authentication, see sample-scripts/auth-pam.pl in the OpenVPN source distribution.

--auth-gen-token [lifetime]

After successful user/password authentication, the OpenVPN server will with this option generate a temporary authentication token and push that to client. On the following renegotiations, the OpenVPN client will pass this token instead of the users password. On the server side the server will do the token authentication internally and it will NOT do any additional authentications against configured external user/password authentication mechanisms.

The lifetime argument defines how long the generated token is valid. The lifetime is defined in seconds. If lifetime is not set or it is set to 0, the token will never expire.

This feature is useful for environments which is configured to use One Time Passwords (OTP) as part of the user/password authentications and that authentication mechanism does not implement any auth-token support.

--opt-verify

Clients that connect with options that are incompatible with those of the server will be disconnected.

Options that will be compared for compatibility include dev-type, link-mtu, tun-mtu, proto, ifconfig, comp-lzo, fragment, keydir, cipher, auth, keysize, secret, no-replay, no-iv, tls-auth, key-method, tls-server, and tls-client.

This option requires that --disable-occ NOT be used.

--auth-user-pass-optional

Allow connections by clients that do not specify a username/password. Normally, when --auth-user-pass-verify or --management-client-auth is specified (or an authentication plugin module), the OpenVPN server daemon will require connecting clients to specify a username and password. This option makes the submission of a username/password by clients optional, passing the responsibility to the user-defined authentication module/script to accept or deny the client based on other factors (such as the setting of X509 certificate fields). When this option is used, and a connecting client does not submit a username/password, the user-defined authentication module/script will see the username and password as being set to empty strings (""). The authentication module/script MUST have logic to detect this condition and respond accordingly.

--client-cert-not-required (DEPRECATED)

Don't require client certificate, client will authenticate using username/password only. Be aware that using this directive is less secure than requiring certificates from all clients.

Please note: This option is now deprecated and will be removed in OpenVPN v2.5. It is replaced by --verify-client-cert which allows for more flexibility. The option --verify-client-cert none is functionally equivalent to --client-cert-not-required

--verify-client-cert none|optional|require

Specify whether the client is required to supply a valid certificate.

Possible options are

none : a client certificate is not required. the client need to authenticate using username/password only. Be aware that using this directive is less secure than requiring certificates from all clients.

If you use this directive, the entire responsibility of authentication will rest on your --auth-user-pass-verify script, so keep in mind that bugs in your script could potentially compromise the security of your VPN.

--verify-client-cert none is functionally equivalent to --client-cert-not-required.

optional : a client may present a certificate but it is not required to do so. When using this directive, you should also use a --auth-user-pass-verify script to ensure that clients are authenticated using a certificate, a username and password, or possibly even both.

Again, the entire responsibility of authentication will rest on your --auth-user-pass-verify script, so keep in mind that bugs in your script could potentially compromise the security of your VPN.

require : this is the default option. A client is required to present a certificate, otherwise VPN access is refused.

If you don't use this directive (or use --verify-client-cert require ) but you also specify an --auth-user-pass-verify script, then OpenVPN will perform double authentication. The client certificate verification AND the --auth-user-pass-verify script will need to succeed in order for a client to be authenticated and accepted onto the VPN.

--username-as-common-name

For --auth-user-pass-verify authentication, use the authenticated username as the common name, rather than the common name from the client cert.

--compat-names [no-remapping] (DEPRECATED)

Until OpenVPN v2.3 the format of the X.509 Subject fields was formatted like this:

/C=US/L=Somewhere/CN=John Doe/emailAddress=john@example.com

In addition the old behaviour was to remap any character other than alphanumeric, underscore ('_'), dash ('-'), dot ('.'), and slash ('/') to underscore ('_'). The X.509 Subject string as returned by the tls_id environmental variable, could additionally contain colon (':') or equal ('=').

When using the --compat-names option, this old formatting and remapping will be re-enabled again. This is purely implemented for compatibility reasons when using older plug-ins or scripts which does not handle the new formatting or UTF-8 characters.

In OpenVPN v2.3 the formatting of these fields changed into a more standardised format. It now looks like:

C=US, L=Somewhere, CN=John Doe, emailAddress=john@example.com

The new default format in OpenVPN v2.3 also does not do the character remapping which happened earlier. This new format enables proper support for UTF-8 characters in the usernames, X.509 Subject fields and Common Name variables and it complies to the RFC 2253, UTF-8 String Representation of Distinguished Names.

The no-remapping mode flag can be used with the --compat-names option to be compatible with the now deprecated --no-name-remapping option. It is only available at the server. When this mode flag is used, the Common Name, Subject, and username strings are allowed to include any printable character including space, but excluding control characters such as tab, newline, and carriage-return. no-remapping is only available on the server side.

Please note: This option is immediately deprecated. It is only implemented to make the transition to the new formatting less intrusive. It will be removed in OpenVPN v2.5. So please update your scripts/plug-ins where necessary.

--no-name-remapping (DEPRECATED)

The --no-name-remapping option is an alias for --compat-names no-remapping. It ensures compatibility with server configurations using the --no-name-remapping option.

Please note: This option is now deprecated. It will be removed in OpenVPN v2.5. So please make sure you support the new X.509 name formatting described with the --compat-names option as soon as possible.

--port-share host port [dir]

When run in TCP server mode, share the OpenVPN port with another application, such as an HTTPS server. If OpenVPN senses a connection to its port which is using a non-OpenVPN protocol, it will proxy the connection to the server at host:port. Currently only designed to work with HTTP/HTTPS, though it would be theoretically possible to extend to other protocols such as ssh.

dir specifies an optional directory where a temporary file with name N containing content C will be dynamically generated for each proxy connection, where N is the source IP:port of the client connection and C is the source IP:port of the connection to the proxy receiver. This directory can be used as a dictionary by the proxy receiver to determine the origin of the connection. Each generated file will be automatically deleted when the proxied connection is torn down.

Not implemented on Windows.

Client Mode

Use client mode when connecting to an OpenVPN server which has --server, --server-bridge, or --mode server in it's configuration.

--client

A helper directive designed to simplify the configuration of OpenVPN's client mode. This directive is equivalent to:

 pull
 tls-client

--pull

This option must be used on a client which is connecting to a multi-client server. It indicates to OpenVPN that it should accept options pushed by the server, provided they are part of the legal set of pushable options (note that the --pull option is implied by --client ).

In particular, --pull allows the server to push routes to the client, so you should not use --pull or --client in situations where you don't trust the server to have control over the client's routing table.

--pull-filter accept|ignore|reject text

Filter options received from the server if the option starts with text. Runs on client. The action flag accept allows the option, ignore removes it and reject flags an error and triggers a SIGUSR1 restart. The filters may be specified multiple times, and each filter is applied in the order it is specified. The filtering of each option stops as soon as a match is found. Unmatched options are accepted by default.

Prefix comparison is used to match text against the received option so that

--pull-filter ignore "route"

would remove all pushed options starting with route which would include, for example, route-gateway. Enclose text in quotes to embed spaces.

--pull-filter accept "route 192.168.1."
--pull-filter ignore "route "

would remove all routes that do not start with 192.168.1.

This option may be used only on clients. Note that reject may result in a repeated cycle of failure and reconnect, unless multiple remotes are specified and connection to the next remote succeeds. To silently ignore an option pushed by the server, use ignore.

--auth-user-pass [up]

Authenticate with server using username/password. up is a file containing username/password on 2 lines. If the password line is missing, OpenVPN will prompt for one.

If up is omitted, username/password will be prompted from the console.

The server configuration must specify an --auth-user-pass-verify script to verify the username/password provided by the client.

--auth-retry type

Controls how OpenVPN responds to username/password verification errors such as the client-side response to an AUTH_FAILED message from the server or verification failure of the private key password.

Normally used to prevent auth errors from being fatal on the client side, and to permit username/password requeries in case of error.

An AUTH_FAILED message is generated by the server if the client fails --auth-user-pass authentication, or if the server-side --client-connect script returns an error status when the client tries to connect.

type can be one of:

none -- Client will exit with a fatal error (this is the default).
nointeract -- Client will retry the connection without requerying for an --auth-user-pass username/password. Use this option for unattended clients.
interact -- Client will requery for an --auth-user-pass username/password and/or private key password before attempting a reconnection.

Note that while this option cannot be pushed, it can be controlled from the management interface.

--static-challenge t e

Enable static challenge/response protocol using challenge text t, with echo flag given by e (0|1).

The echo flag indicates whether or not the user's response to the challenge should be echoed.

See management-notes.txt in the OpenVPN distribution for a description of the OpenVPN challenge/response protocol.

--server-poll-timeout n

--connect-timeout n when connecting to a remote server do not wait for more than n seconds waiting for a response before trying the next server. The default value is 120s. This timeout includes proxy and TCP connect timeouts.

--explicit-exit-notify [n]

In UDP client mode or point-to-point mode, send server/peer an exit notification if tunnel is restarted or OpenVPN process is exited. In client mode, on exit/restart, this option will tell the server to immediately close its client instance object rather than waiting for a timeout. The n parameter (default=1) controls the maximum number of attempts that the client will try to resend the exit notification message.

In UDP server mode, send RESTART control channel command to connected clients. The n parameter (default=1) controls client behavior. With n = 1 client will attempt to reconnect to the same server, with n = 2 client will advance to the next server.

OpenVPN will not send any exit notifications unless this option is enabled.

--allow-recursive-routing

When this option is set, OpenVPN will not drop incoming tun packets with same destination as host.

Data Channel Encryption Options:

These options are meaningful for both Static & TLS-negotiated key modes (must be compatible between peers).

--secret file [direction]

Enable Static Key encryption mode (non-TLS). Use pre-shared secret file which was generated with --genkey.

The optional direction parameter enables the use of 4 distinct keys (HMAC-send, cipher-encrypt, HMAC-receive, cipher-decrypt), so that each data flow direction has a different set of HMAC and cipher keys. This has a number of desirable security properties including eliminating certain kinds of DoS and message replay attacks.

When the direction parameter is omitted, 2 keys are used bidirectionally, one for HMAC and the other for encryption/decryption.

The direction parameter should always be complementary on either side of the connection, i.e. one side should use "0" and the other should use "1", or both sides should omit it altogether.

The direction parameter requires that file contains a 2048 bit key. While pre-1.5 versions of OpenVPN generate 1024 bit key files, any version of OpenVPN which supports the direction parameter, will also support 2048 bit key file generation using the --genkey option.

Static key encryption mode has certain advantages, the primary being ease of configuration.

There are no certificates or certificate authorities or complicated negotiation handshakes and protocols. The only requirement is that you have a pre-existing secure channel with your peer (such as ssh ) to initially copy the key. This requirement, along with the fact that your key never changes unless you manually generate a new one, makes it somewhat less secure than TLS mode (see below). If an attacker manages to steal your key, everything that was ever encrypted with it is compromised. Contrast that to the perfect forward secrecy features of TLS mode (using Diffie Hellman key exchange), where even if an attacker was able to steal your private key, he would gain no information to help him decrypt past sessions.

Another advantageous aspect of Static Key encryption mode is that it is a handshake-free protocol without any distinguishing signature or feature (such as a header or protocol handshake sequence) that would mark the ciphertext packets as being generated by OpenVPN. Anyone eavesdropping on the wire would see nothing but random-looking data.

--key-direction

Alternative way of specifying the optional direction parameter for the --tls-auth and --secret options. Useful when using inline files (See section on inline files).

--auth alg

Authenticate data channel packets and (if enabled) tls-auth control channel packets with HMAC using message digest algorithm alg. (The default is SHA1 ). HMAC is a commonly used message authentication algorithm (MAC) that uses a data string, a secure hash algorithm, and a key, to produce a digital signature.

The OpenVPN data channel protocol uses encrypt-then-mac (i.e. first encrypt a packet, then HMAC the resulting ciphertext), which prevents padding oracle attacks.

If an AEAD cipher mode (e.g. GCM) is chosen, the specified --auth algorithm is ignored for the data channel, and the authentication method of the AEAD cipher is used instead. Note that alg still specifies the digest used for tls-auth.

In static-key encryption mode, the HMAC key is included in the key file generated by --genkey. In TLS mode, the HMAC key is dynamically generated and shared between peers via the TLS control channel. If OpenVPN receives a packet with a bad HMAC it will drop the packet. HMAC usually adds 16 or 20 bytes per packet. Set alg=none to disable authentication.

For more information on HMAC see http://www.cs.ucsd.edu/users/mihir/papers/hmac.html

--cipher alg

Encrypt data channel packets with cipher algorithm alg. The default is BF-CBC, an abbreviation for Blowfish in Cipher Block Chaining mode.

Using BF-CBC is no longer recommended, because of it's 64-bit block size. This small block size allows attacks based on collisions, as demonstrated by SWEET32. See https://community.openvpn.net/openvpn/wiki/SWEET32 for details.

To see other ciphers that are available with OpenVPN, use the --show-ciphers option.

Set alg=none to disable encryption.

As of OpenVPN 2.4, cipher negotiation (NCP) can override the cipher specified by --cipher. See --ncp-ciphers and --ncp-disable for more on NCP.

--ncp-ciphers cipher_list

Restrict the allowed ciphers to be negotiated to the ciphers in cipher_list. cipher_list is a colon-separated list of ciphers, and defaults to "AES-256-GCM:AES-128-GCM".

For servers, the first cipher from cipher_list will be pushed to clients that support cipher negotiation.

Cipher negotiation is enabled in client-server mode only. I.e. if --mode is set to 'server' (server-side, implied by setting --server ), or if --pull is specified (client-side, implied by setting --client).

If both peers support and do not disable NCP, the negotiated cipher will override the cipher specified by --cipher.

Additionally, to allow for more smooth transition, if NCP is enabled, OpenVPN will inherit the cipher of the peer if that cipher is different from the local --cipher setting, but the peer cipher is one of the ciphers specified in --ncp-ciphers. E.g. a non-NCP client (<=2.3, or with --ncp-disabled set) connecting to a NCP server (2.4+) with "--cipher BF-CBC" and "--ncp-ciphers AES-256-GCM:AES-256-CBC" set can either specify "--cipher BF-CBC" or "--cipher AES-256-CBC" and both will work.

--ncp-disable

Disable "negotiable crypto parameters". This completely disables cipher negotiation.

--keysize n

Size of cipher key in bits (optional). If unspecified, defaults to cipher-specific default. The --show-ciphers option (see below) shows all available OpenSSL ciphers, their default key sizes, and whether the key size can be changed. Use care in changing a cipher's default key size. Many ciphers have not been extensively cryptanalyzed with non-standard key lengths, and a larger key may offer no real guarantee of greater security, or may even reduce security.

--prng alg [nsl]

(Advanced) For PRNG (Pseudo-random number generator), use digest algorithm alg (default=sha1), and set nsl (default=16) to the size in bytes of the nonce secret length (between 16 and 64).

Set alg=none to disable the PRNG and use the OpenSSL RAND_bytes function instead for all of OpenVPN's pseudo-random number needs.

--engine [engine-name]

Enable OpenSSL hardware-based crypto engine functionality.

If engine-name is specified, use a specific crypto engine. Use the --show-engines standalone option to list the crypto engines which are supported by OpenSSL.

--no-replay

(Advanced) Disable OpenVPN's protection against replay attacks. Don't use this option unless you are prepared to make a tradeoff of greater efficiency in exchange for less security.

OpenVPN provides datagram replay protection by default.

Replay protection is accomplished by tagging each outgoing datagram with an identifier that is guaranteed to be unique for the key being used. The peer that receives the datagram will check for the uniqueness of the identifier. If the identifier was already received in a previous datagram, OpenVPN will drop the packet. Replay protection is important to defeat attacks such as a SYN flood attack, where the attacker listens in the wire, intercepts a TCP SYN packet (identifying it by the context in which it occurs in relation to other packets), then floods the receiving peer with copies of this packet.

OpenVPN's replay protection is implemented in slightly different ways, depending on the key management mode you have selected.

In Static Key mode or when using an CFB or OFB mode cipher, OpenVPN uses a 64 bit unique identifier that combines a time stamp with an incrementing sequence number.

When using TLS mode for key exchange and a CBC cipher mode, OpenVPN uses only a 32 bit sequence number without a time stamp, since OpenVPN can guarantee the uniqueness of this value for each key. As in IPSec, if the sequence number is close to wrapping back to zero, OpenVPN will trigger a new key exchange.

To check for replays, OpenVPN uses the sliding window algorithm used by IPSec.

--replay-window n [t]

Use a replay protection sliding-window of size n and a time window of t seconds.

By default n is 64 (the IPSec default) and t is 15 seconds.

This option is only relevant in UDP mode, i.e. when either --proto udp is specified, or no --proto option is specified.

When OpenVPN tunnels IP packets over UDP, there is the possibility that packets might be dropped or delivered out of order. Because OpenVPN, like IPSec, is emulating the physical network layer, it will accept an out-of-order packet sequence, and will deliver such packets in the same order they were received to the TCP/IP protocol stack, provided they satisfy several constraints.

(a) The packet cannot be a replay (unless --no-replay is specified, which disables replay protection altogether).

(b) If a packet arrives out of order, it will only be accepted if the difference between its sequence number and the highest sequence number received so far is less than n.

(c) If a packet arrives out of order, it will only be accepted if it arrives no later than t seconds after any packet containing a higher sequence number.

If you are using a network link with a large pipeline (meaning that the product of bandwidth and latency is high), you may want to use a larger value for n. Satellite links in particular often require this.

If you run OpenVPN at --verb 4, you will see the message "Replay-window backtrack occurred [x]" every time the maximum sequence number backtrack seen thus far increases. This can be used to calibrate n.

There is some controversy on the appropriate method of handling packet reordering at the security layer.

Namely, to what extent should the security layer protect the encapsulated protocol from attacks which masquerade as the kinds of normal packet loss and reordering that occur over IP networks?

The IPSec and OpenVPN approach is to allow packet reordering within a certain fixed sequence number window.

OpenVPN adds to the IPSec model by limiting the window size in time as well as sequence space.

OpenVPN also adds TCP transport as an option (not offered by IPSec) in which case OpenVPN can adopt a very strict attitude towards message deletion and reordering: Don't allow it. Since TCP guarantees reliability, any packet loss or reordering event can be assumed to be an attack.

In this sense, it could be argued that TCP tunnel transport is preferred when tunneling non-IP or UDP application protocols which might be vulnerable to a message deletion or reordering attack which falls within the normal operational parameters of IP networks.

So I would make the statement that one should never tunnel a non-IP protocol or UDP application protocol over UDP, if the protocol might be vulnerable to a message deletion or reordering attack that falls within the normal operating parameters of what is to be expected from the physical IP layer. The problem is easily fixed by simply using TCP as the VPN transport layer.

--mute-replay-warnings

Silence the output of replay warnings, which are a common false alarm on WiFi networks. This option preserves the security of the replay protection code without the verbosity associated with warnings about duplicate packets.

--replay-persist file

Persist replay-protection state across sessions using file to save and reload the state.

This option will strengthen protection against replay attacks, especially when you are using OpenVPN in a dynamic context (such as with --inetd) when OpenVPN sessions are frequently started and stopped.

This option will keep a disk copy of the current replay protection state (i.e. the most recent packet timestamp and sequence number received from the remote peer), so that if an OpenVPN session is stopped and restarted, it will reject any replays of packets which were already received by the prior session.

This option only makes sense when replay protection is enabled (the default) and you are using either --secret (shared-secret key mode) or TLS mode with --tls-auth.

--no-iv

DEPRECATED This option will be removed in OpenVPN 2.5.

(Advanced) Disable OpenVPN's use of IV (cipher initialization vector). Don't use this option unless you are prepared to make a tradeoff of greater efficiency in exchange for less security.

OpenVPN uses an IV by default, and requires it for CFB and OFB cipher modes (which are totally insecure without it). Using an IV is important for security when multiple messages are being encrypted/decrypted with the same key.

IV is implemented differently depending on the cipher mode used.

In CBC mode, OpenVPN uses a pseudo-random IV for each packet.

In CFB/OFB mode, OpenVPN uses a unique sequence number and time stamp as the IV. In fact, in CFB/OFB mode, OpenVPN uses a datagram space-saving optimization that uses the unique identifier for datagram replay protection as the IV.

--use-prediction-resistance

Enable prediction resistance on PolarSSL's RNG.

Enabling prediction resistance causes the RNG to reseed in each call for random. Reseeding this often can quickly deplete the kernel entropy pool.

If you need this option, please consider running a daemon that adds entropy to the kernel pool.

Note that this option only works with PolarSSL versions greater than 1.1.

--test-crypto

Do a self-test of OpenVPN's crypto options by encrypting and decrypting test packets using the data channel encryption options specified above. This option does not require a peer to function, and therefore can be specified without --dev or --remote.

The typical usage of --test-crypto would be something like this:

openvpn --test-crypto --secret key

openvpn --test-crypto --secret key --verb 9

This option is very useful to test OpenVPN after it has been ported to a new platform, or to isolate problems in the compiler, OpenSSL crypto library, or OpenVPN's crypto code. Since it is a self-test mode, problems with encryption and authentication can be debugged independently of network and tunnel issues.

TLS Mode Options:

TLS mode is the most powerful crypto mode of OpenVPN in both security and flexibility. TLS mode works by establishing control and data channels which are multiplexed over a single TCP/UDP port. OpenVPN initiates a TLS session over the control channel and uses it to exchange cipher and HMAC keys to protect the data channel. TLS mode uses a robust reliability layer over the UDP connection for all control channel communication, while the data channel, over which encrypted tunnel data passes, is forwarded without any mediation. The result is the best of both worlds: a fast data channel that forwards over UDP with only the overhead of encrypt, decrypt, and HMAC functions, and a control channel that provides all of the security features of TLS, including certificate-based authentication and Diffie Hellman forward secrecy.

To use TLS mode, each peer that runs OpenVPN should have its own local certificate/key pair ( --cert and --key ), signed by the root certificate which is specified in --ca.

When two OpenVPN peers connect, each presents its local certificate to the other. Each peer will then check that its partner peer presented a certificate which was signed by the master root certificate as specified in --ca.

If that check on both peers succeeds, then the TLS negotiation will succeed, both OpenVPN peers will exchange temporary session keys, and the tunnel will begin passing data.

The OpenVPN project provides a set of scripts for managing RSA certificates & keys: https://github.com/OpenVPN/easy-rsa

--tls-server

Enable TLS and assume server role during TLS handshake. Note that OpenVPN is designed as a peer-to-peer application. The designation of client or server is only for the purpose of negotiating the TLS control channel.

--tls-client

Enable TLS and assume client role during TLS handshake.

--ca file

Certificate authority (CA) file in .pem format, also referred to as the root certificate. This file can have multiple certificates in .pem format, concatenated together. You can construct your own certificate authority certificate and private key by using a command such as:

openssl req -nodes -new -x509 -keyout ca.key -out ca.crt

Then edit your openssl.cnf file and edit the certificate variable to point to your new root certificate ca.crt.

For testing purposes only, the OpenVPN distribution includes a sample CA certificate (ca.crt). Of course you should never use the test certificates and test keys distributed with OpenVPN in a production environment, since by virtue of the fact that they are distributed with OpenVPN, they are totally insecure.

--capath dir

Directory containing trusted certificates (CAs and CRLs). Not available with PolarSSL.

When using the --capath option, you are required to supply valid CRLs for the CAs too. CAs in the capath directory are expected to be named <hash>.<n>. CRLs are expected to be named <hash>.r<n>. See the -CApath option of openssl verify , and the -hash option of openssl x509 and openssl crl for more information.

--dh file

File containing Diffie Hellman parameters in .pem format (required for --tls-server only).

Set file=none to disable Diffie Hellman key exchange (and use ECDH only). Note that this requires peers to be using an SSL library that supports ECDH TLS cipher suites (e.g. OpenSSL 1.0.1+, or PolarSSL 1.3+).

Use openssl dhparam -out dh2048.pem 2048 to generate 2048-bit DH parameters. Diffie Hellman parameters may be considered public.

--ecdh-curve name

Specify the curve to use for elliptic curve Diffie Hellman. Available curves can be listed with --show-curves. The specified curve will only be used for ECDH TLS-ciphers.

This option is not supported in mbed TLS builds of OpenVPN.

--cert file

Local peer's signed certificate in .pem format -- must be signed by a certificate authority whose certificate is in --ca file. Each peer in an OpenVPN link running in TLS mode should have its own certificate and private key file. In addition, each certificate should have been signed by the key of a certificate authority whose public key resides in the --ca certificate authority file. You can easily make your own certificate authority (see above) or pay money to use a commercial service such as thawte.com (in which case you will be helping to finance the world's second space tourist :). To generate a certificate, you can use a command such as:

openssl req -nodes -new -keyout mycert.key -out mycert.csr

If your certificate authority private key lives on another machine, copy the certificate signing request (mycert.csr) to this other machine (this can be done over an insecure channel such as email). Now sign the certificate with a command such as:

openssl ca -out mycert.crt -in mycert.csr

Now copy the certificate (mycert.crt) back to the peer which initially generated the .csr file (this can be over a public medium). Note that the openssl ca command reads the location of the certificate authority key from its configuration file such as /usr/share/ssl/openssl.cnf -- note also that for certificate authority functions, you must set up the files index.txt (may be empty) and serial (initialize to 01 ).

--extra-certs file

Specify a file containing one or more PEM certs (concatenated together) that complete the local certificate chain.

This option is useful for "split" CAs, where the CA for server certs is different than the CA for client certs. Putting certs in this file allows them to be used to complete the local certificate chain without trusting them to verify the peer-submitted certificate, as would be the case if the certs were placed in the ca file.

--key file

Local peer's private key in .pem format. Use the private key which was generated when you built your peer's certificate (see --cert file above).

--tls-version-min version ['or-highest']

Sets the minimum TLS version we will accept from the peer (default is "1.0"). Examples for version include "1.0", "1.1", or "1.2". If 'or-highest' is specified and version is not recognized, we will only accept the highest TLS version supported by the local SSL implementation.

--tls-version-max version

Set the maximum TLS version we will use (default is the highest version supported). Examples for version include "1.0", "1.1", or "1.2".

--pkcs12 file

Specify a PKCS #12 file containing local private key, local certificate, and root CA certificate. This option can be used instead of --ca, --cert, and --key. Not available with PolarSSL.

--verify-hash hash

Specify SHA1 fingerprint for level-1 cert. The level-1 cert is the CA (or intermediate cert) that signs the leaf certificate, and is one removed from the leaf certificate in the direction of the root. When accepting a connection from a peer, the level-1 cert fingerprint must match hash or certificate verification will fail. Hash is specified as XX:XX:... For example: AD:B0:95:D8:09:C8:36:45:12:A9:89:C8:90:09:CB:13:72:A6:AD:16

--pkcs11-cert-private [0|1]...

Set if access to certificate object should be performed after login. Every provider has its own setting.

--pkcs11-id name

Specify the serialized certificate id to be used. The id can be gotten by the standalone --show-pkcs11-ids option.

--pkcs11-id-management

Acquire PKCS#11 id from management interface. In this case a NEED-STR 'pkcs11-id-request' real-time message will be triggered, application may use pkcs11-id-count command to retrieve available number of certificates, and pkcs11-id-get command to retrieve certificate id and certificate body.

--pkcs11-pin-cache seconds

Specify how many seconds the PIN can be cached, the default is until the token is removed.

--pkcs11-protected-authentication [0|1]...

Use PKCS#11 protected authentication path, useful for biometric and external keypad devices. Every provider has its own setting.

--pkcs11-providers provider...

Specify a RSA Security Inc. PKCS #11 Cryptographic Token Interface (Cryptoki) providers to load. This option can be used instead of --cert, --key, and --pkcs12.

If p11-kit is present on the system, its p11-kit-proxy.so module will be loaded by default if either the --pkcs11-id or --pkcs11-id-management options are specified without --pkcs11-provider being given.

--pkcs11-private-mode mode...

Specify which method to use in order to perform private key operations. A different mode can be specified for each provider. Mode is encoded as hex number, and can be a mask one of the following:

0 (default) -- Try to determine automatically.
1 -- Use sign.
2 -- Use sign recover.
4 -- Use decrypt.
8 -- Use unwrap.

--cryptoapicert select-string

Load the certificate and private key from the Windows Certificate System Store (Windows/OpenSSL Only).

Use this option instead of --cert and --key.

This makes it possible to use any smart card, supported by Windows, but also any kind of certificate, residing in the Cert Store, where you have access to the private key. This option has been tested with a couple of different smart cards (GemSAFE, Cryptoflex, and Swedish Post Office eID) on the client side, and also an imported PKCS12 software certificate on the server side.

To select a certificate, based on a substring search in the certificate's subject:

cryptoapicert "SUBJ:Peter Runestig"

To select a certificate, based on certificate's thumbprint:

cryptoapicert "THUMB:f6 49 24 41 01 b4 ..."

The thumbprint hex string can easily be copy-and-pasted from the Windows Certificate Store GUI.

--key-method m

Use data channel key negotiation method m. The key method must match on both sides of the connection.

After OpenVPN negotiates a TLS session, a new set of keys for protecting the tunnel data channel is generated and exchanged over the TLS session.

In method 1 (the default for OpenVPN 1.x), both sides generate random encrypt and HMAC-send keys which are forwarded to the other host over the TLS channel. Method 1 is deprecated in OpenVPN 2.4 , and will be removed in OpenVPN 2.5.

In method 2, (the default for OpenVPN 2.0) the client generates a random key. Both client and server also generate some random seed material. All key source material is exchanged over the TLS channel. The actual keys are generated using the TLS PRF function, taking source entropy from both client and server. Method 2 is designed to closely parallel the key generation process used by TLS 1.0.

Note that in TLS mode, two separate levels of keying occur:

(1) The TLS connection is initially negotiated, with both sides of the connection producing certificates and verifying the certificate (or other authentication info provided) of the other side. The --key-method parameter has no effect on this process.

(2) After the TLS connection is established, the tunnel session keys are separately negotiated over the existing secure TLS channel. Here, --key-method determines the derivation of the tunnel session keys.

--tls-cipher l

A list l of allowable TLS ciphers delimited by a colon (":").

This setting can be used to ensure that certain cipher suites are used (or not used) for the TLS connection. OpenVPN uses TLS to secure the control channel, over which the keys that are used to protect the actual VPN traffic are exchanged.

The supplied list of ciphers is (after potential OpenSSL/IANA name translation) simply supplied to the crypto library. Please see the OpenSSL and/or PolarSSL documentation for details on the cipher list interpretation.

Use --show-tls to see a list of TLS ciphers supported by your crypto library.

Warning! --tls-cipher is an expert feature, which - if used correcly - can improve the security of your VPN connection. But it is also easy to unwittingly use it to carefully align a gun with your foot, or just break your connection. Use with care!

The default for --tls-cipher is to use PolarSSL's default cipher list when using PolarSSL or "DEFAULT:!EXP:!LOW:!MEDIUM:!kDH:!kECDH:!DSS:!PSK:!SRP:!kRSA" when using OpenSSL.

--tls-timeout n

Packet retransmit timeout on TLS control channel if no acknowledgment from remote within n seconds (default=2). When OpenVPN sends a control packet to its peer, it will expect to receive an acknowledgement within n seconds or it will retransmit the packet, subject to a TCP-like exponential backoff algorithm. This parameter only applies to control channel packets. Data channel packets (which carry encrypted tunnel data) are never acknowledged, sequenced, or retransmitted by OpenVPN because the higher level network protocols running on top of the tunnel such as TCP expect this role to be left to them.

--reneg-bytes n

Renegotiate data channel key after n bytes sent or received (disabled by default with an exception, see below). OpenVPN allows the lifetime of a key to be expressed as a number of bytes encrypted/decrypted, a number of packets, or a number of seconds. A key renegotiation will be forced if any of these three criteria are met by either peer.

If using ciphers with cipher block sizes less than 128-bits, --reneg-bytes is set to 64MB by default, unless it is explicitly disabled by setting the value to 0, but this is HIGHLY DISCOURAGED as this is designed to add some protection against the SWEET32 attack vector. For more information see the --cipher option.

--reneg-pkts n

Renegotiate data channel key after n packets sent and received (disabled by default).

--reneg-sec n

Renegotiate data channel key after n seconds (default=3600).

When using dual-factor authentication, note that this default value may cause the end user to be challenged to reauthorize once per hour.

Also, keep in mind that this option can be used on both the client and server, and whichever uses the lower value will be the one to trigger the renegotiation. A common mistake is to set --reneg-sec to a higher value on either the client or server, while the other side of the connection is still using the default value of 3600 seconds, meaning that the renegotiation will still occur once per 3600 seconds. The solution is to increase --reneg-sec on both the client and server, or set it to 0 on one side of the connection (to disable), and to your chosen value on the other side.

--hand-window n

Handshake Window -- the TLS-based key exchange must finalize within n seconds of handshake initiation by any peer (default = 60 seconds). If the handshake fails we will attempt to reset our connection with our peer and try again. Even in the event of handshake failure we will still use our expiring key for up to --tran-window seconds to maintain continuity of transmission of tunnel data.

--tran-window n

Transition window -- our old key can live this many seconds after a new a key renegotiation begins (default = 3600 seconds). This feature allows for a graceful transition from old to new key, and removes the key renegotiation sequence from the critical path of tunnel data forwarding.

--single-session

After initially connecting to a remote peer, disallow any new connections. Using this option means that a remote peer cannot connect, disconnect, and then reconnect.

If the daemon is reset by a signal or --ping-restart, it will allow one new connection.

--single-session can be used with --ping-exit or --inactive to create a single dynamic session that will exit when finished.

--tls-exit

Exit on TLS negotiation failure.

--tls-auth file [direction]

Add an additional layer of HMAC authentication on top of the TLS control channel to mitigate DoS attacks and attacks on the TLS stack.

In a nutshell, --tls-auth enables a kind of "HMAC firewall" on OpenVPN's TCP/UDP port, where TLS control channel packets bearing an incorrect HMAC signature can be dropped immediately without response.

file (required) is a file in OpenVPN static key format which can be generated by --genkey

Older versions (up to 2.3) supported a freeform passphrase file. This is no longer supported in newer versions (2.4+).

See the --secret option for more information on the optional direction parameter.

--tls-auth is recommended when you are running OpenVPN in a mode where it is listening for packets from any IP address, such as when --remote is not specified, or --remote is specified with --float.

The rationale for this feature is as follows. TLS requires a multi-packet exchange before it is able to authenticate a peer. During this time before authentication, OpenVPN is allocating resources (memory and CPU) to this potential peer. The potential peer is also exposing many parts of OpenVPN and the OpenSSL library to the packets it is sending. Most successful network attacks today seek to either exploit bugs in programs (such as buffer overflow attacks) or force a program to consume so many resources that it becomes unusable. Of course the first line of defense is always to produce clean, well-audited code. OpenVPN has been written with buffer overflow attack prevention as a top priority. But as history has shown, many of the most widely used network applications have, from time to time, fallen to buffer overflow attacks.

So as a second line of defense, OpenVPN offers this special layer of authentication on top of the TLS control channel so that every packet on the control channel is authenticated by an HMAC signature and a unique ID for replay protection. This signature will also help protect against DoS (Denial of Service) attacks. An important rule of thumb in reducing vulnerability to DoS attacks is to minimize the amount of resources a potential, but as yet unauthenticated, client is able to consume.

--tls-auth does this by signing every TLS control channel packet with an HMAC signature, including packets which are sent before the TLS level has had a chance to authenticate the peer. The result is that packets without the correct signature can be dropped immediately upon reception, before they have a chance to consume additional system resources such as by initiating a TLS handshake. --tls-auth can be strengthened by adding the --replay-persist option which will keep OpenVPN's replay protection state in a file so that it is not lost across restarts.

It should be emphasized that this feature is optional and that the key file used with --tls-auth gives a peer nothing more than the power to initiate a TLS handshake. It is not used to encrypt or authenticate any tunnel data.

Use --tls-crypt instead if you want to use the key file to not only authenticate, but also encrypt the TLS control channel.

--tls-crypt keyfile

Encrypt and authenticate all control channel packets with the key from keyfile. (See --tls-auth for more background.)

Encrypting (and authenticating) control channel packets:

[bu]: provides more privacy by hiding the certificate used for the TLS connection,
[bu]: makes it harder to identify OpenVPN traffic as such,
[bu]: provides "poor-man's" post-quantum security, against attackers who will never know the pre-shared key (i.e. no forward secrecy).

In contrast to --tls-auth, --tls-crypt does *not* require the user to set --key-direction.

--askpass [file]

Get certificate password from console or file before we daemonize.

For the extremely security conscious, it is possible to protect your private key with a password. Of course this means that every time the OpenVPN daemon is started you must be there to type the password. The --askpass option allows you to start OpenVPN from the command line. It will query you for a password before it daemonizes. To protect a private key with a password you should omit the -nodes option when you use the openssl command line tool to manage certificates and private keys.

If file is specified, read the password from the first line of file. Keep in mind that storing your password in a file to a certain extent invalidates the extra security provided by using an encrypted key.

--auth-nocache

Don't cache --askpass or --auth-user-pass username/passwords in virtual memory.

If specified, this directive will cause OpenVPN to immediately forget username/password inputs after they are used. As a result, when OpenVPN needs a username/password, it will prompt for input from stdin, which may be multiple times during the duration of an OpenVPN session.

When using --auth-nocache in combination with a user/password file and --chroot or --daemon, make sure to use an absolute path.

This directive does not affect the --http-proxy username/password. It is always cached.

--auth-token token

This is not an option to be used directly in any configuration files, but rather push this option from a --client-connect script or a --plugin which hooks into the OPENVPN_PLUGIN_CLIENT_CONNECT or OPENVPN_PLUGIN_CLIENT_CONNECT_V2 calls. This option provides a possibility to replace the clients password with an authentication token during the lifetime of the OpenVPN client.

Whenever the connection is renegotiated and the --auth-user-pass-verify script or --plugin making use of the OPENVPN_PLUGIN_AUTH_USER_PASS_VERIFY hook is triggered, it will pass over this token as the password instead of the password the user provided. The authentication token can only be reset by a full reconnect where the server can push new options to the client. The password the user entered is never preserved once an authentication token have been set. If the OpenVPN server side rejects the authentication token, the client will receive an AUTH_FAIL and disconnect.

The purpose of this is to enable two factor authentication methods, such as HOTP or TOTP, to be used without needing to retrieve a new OTP code each time the connection is renegotiated. Another use case is to cache authentication data on the client without needing to have the users password cached in memory during the life time of the session.

To make use of this feature, the --client-connect script or --plugin needs to put

push "auth-token UNIQUE_TOKEN_VALUE"

into the file/buffer for dynamic configuration data. This will then make the OpenVPN server to push this value to the client, which replaces the local password with the UNIQUE_TOKEN_VALUE.

--tls-verify cmd

Run command cmd to verify the X509 name of a pending TLS connection that has otherwise passed all other tests of certification (except for revocation via --crl-verify directive; the revocation test occurs after the --tls-verify test).

cmd should return 0 to allow the TLS handshake to proceed, or 1 to fail.

When cmd is executed two arguments are appended after any arguments specified in cmd , as follows:

cmd certificate_depth subject

These arguments are, respectively, the current certificate depth and the X509 common name (cn) of the peer.

This feature is useful if the peer you want to trust has a certificate which was signed by a certificate authority who also signed many other certificates, where you don't necessarily want to trust all of them, but rather be selective about which peer certificate you will accept. This feature allows you to write a script which will test the X509 name on a certificate and decide whether or not it should be accepted. For a simple perl script which will test the common name field on the certificate, see the file verify-cn in the OpenVPN distribution.

See the "Environmental Variables" section below for additional parameters passed as environmental variables.

--tls-export-cert directory

Store the certificates the clients uses upon connection to this directory. This will be done before --tls-verify is called. The certificates will use a temporary name and will be deleted when the tls-verify script returns. The file name used for the certificate is available via the peer_cert environment variable.

--x509-username-field [ext:]fieldname

Field in the X.509 certificate subject to be used as the username (default=CN). Typically, this option is specified with fieldname as either of the following:

--x509-username-field emailAddress
--x509-username-field ext:subjectAltName

The first example uses the value of the "emailAddress" attribute in the certificate's Subject field as the username. The second example uses the ext: prefix to signify that the X.509 extension fieldname "subjectAltName" be searched for an rfc822Name (email) field to be used as the username. In cases where there are multiple email addresses in ext:fieldname, the last occurrence is chosen.

When this option is used, the --verify-x509-name option will match against the chosen fieldname instead of the Common Name.

Please note: This option has a feature which will convert an all-lowercase fieldname to uppercase characters, e.g., ou -> OU. A mixed-case fieldname or one having the ext: prefix will be left as-is. This automatic upcasing feature is deprecated and will be removed in a future release.

--verify-x509-name name type

Accept connections only if a host's X.509 name is equal to name. The remote host must also pass all other tests of verification.

Which X.509 name is compared to name depends on the setting of type. type can be "subject" to match the complete subject DN (default), "name" to match a subject RDN or "name-prefix" to match a subject RDN prefix. Which RDN is verified as name depends on the --x509-username-field option. But it defaults to the common name (CN), e.g. a certificate with a subject DN "C=KG, ST=NA, L=Bishkek, CN=Server-1" would be matched by:

--verify-x509-name 'C=KG, ST=NA, L=Bishkek, CN=Server-1' and --verify-x509-name Server-1 name or you could use --verify-x509-name Server -name-prefix if you want a client to only accept connections to "Server-1", "Server-2", etc.

--verify-x509-name is a useful replacement for the --tls-verify option to verify the remote host, because --verify-x509-name works in a --chroot environment without any dependencies.

Using a name prefix is a useful alternative to managing a CRL (Certificate Revocation List) on the client, since it allows the client to refuse all certificates except for those associated with designated servers.

NOTE: Test against a name prefix only when you are using OpenVPN with a custom CA certificate that is under your control. Never use this option with type "name-prefix" when your client certificates are signed by a third party, such as a commercial web CA.

--x509-track attribute

Save peer X509 attribute value in environment for use by plugins and management interface. Prepend a '+' to attribute to save values from full cert chain. Values will be encoded as X509_<depth>_<attribute>=<value>. Multiple --x509-track options can be defined to track multiple attributes.

--ns-cert-type client|server

Require that peer certificate was signed with an explicit nsCertType designation of "client" or "server".

This is a useful security option for clients, to ensure that the host they connect with is a designated server.

See the easy-rsa/build-key-server script for an example of how to generate a certificate with the nsCertType field set to "server".

If the server certificate's nsCertType field is set to "server", then the clients can verify this with --ns-cert-type server.

This is an important security precaution to protect against a man-in-the-middle attack where an authorized client attempts to connect to another client by impersonating the server. The attack is easily prevented by having clients verify the server certificate using any one of --ns-cert-type, --verify-x509-name, or --tls-verify.

--remote-cert-ku v...

Require that peer certificate was signed with an explicit key usage.

This is a useful security option for clients, to ensure that the host they connect to is a designated server.

The key usage should be encoded in hex, more than one key usage can be specified.

--remote-cert-eku oid

Require that peer certificate was signed with an explicit extended key usage.

This is a useful security option for clients, to ensure that the host they connect to is a designated server.

The extended key usage should be encoded in oid notation, or OpenSSL symbolic representation.

--remote-cert-tls client|server

Require that peer certificate was signed with an explicit key usage and extended key usage based on RFC3280 TLS rules.

This is a useful security option for clients, to ensure that the host they connect to is a designated server.

The --remote-cert-tls client option is equivalent to --remote-cert-ku 80 08 88 --remote-cert-eku "TLS Web Client Authentication"

The key usage is digitalSignature and/or keyAgreement.

The --remote-cert-tls server option is equivalent to --remote-cert-ku a0 88 --remote-cert-eku "TLS Web Server Authentication"

The key usage is digitalSignature and ( keyEncipherment or keyAgreement ).

This is an important security precaution to protect against a man-in-the-middle attack where an authorized client attempts to connect to another client by impersonating the server. The attack is easily prevented by having clients verify the server certificate using any one of --remote-cert-tls, --verify-x509-name, or --tls-verify.

--crl-verify crl ['dir']

Check peer certificate against the file crl in PEM format.

A CRL (certificate revocation list) is used when a particular key is compromised but when the overall PKI is still intact.

Suppose you had a PKI consisting of a CA, root certificate, and a number of client certificates. Suppose a laptop computer containing a client key and certificate was stolen. By adding the stolen certificate to the CRL file, you could reject any connection which attempts to use it, while preserving the overall integrity of the PKI.

The only time when it would be necessary to rebuild the entire PKI from scratch would be if the root certificate key itself was compromised.

If the optional dir flag is specified, enable a different mode where crl is a directory containing files named as revoked serial numbers (the files may be empty, the contents are never read). If a client requests a connection, where the client certificate serial number (decimal string) is the name of a file present in the directory, it will be rejected.

Note: As the crl file (or directory) is read every time a peer connects, if you are dropping root privileges with --user, make sure that this user has sufficient privileges to read the file.

SSL Library information:

--show-ciphers: (Standalone) Show all cipher algorithms to use with the --cipher option.
--show-digests: (Standalone) Show all message digest algorithms to use with the --auth option.
--show-tls: (Standalone) Show all TLS ciphers supported by the crypto library. OpenVPN uses TLS to secure the control channel, over which the keys that are used to protect the actual VPN traffic are exchanged. The TLS ciphers will be sorted from highest preference (most secure) to lowest.
Be aware that whether a cipher suite in this list can actually work depends on the specific setup of both peers (e.g. both peers must support the cipher, and an ECDSA cipher suite will not work if you are using an RSA certificate, etc.).
--show-engines: (Standalone) Show currently available hardware-based crypto acceleration engines supported by the OpenSSL library.
--show-curves: (Standalone) Show all available elliptic curves to use with the --ecdh-curve option.

Generate a random key:

Used only for non-TLS static key encryption mode.

--genkey: (Standalone) Generate a random key to be used as a shared secret, for use with the --secret option. This file must be shared with the peer over a pre-existing secure channel such as scp(1)
--secret file: Write key to file.

TUN/TAP persistent tunnel config mode:

Available with linux 2.4.7+. These options comprise a standalone mode of OpenVPN which can be used to create and delete persistent tunnels.

--mktun

(Standalone) Create a persistent tunnel on platforms which support them such as Linux. Normally TUN/TAP tunnels exist only for the period of time that an application has them open. This option takes advantage of the TUN/TAP driver's ability to build persistent tunnels that live through multiple instantiations of OpenVPN and die only when they are deleted or the machine is rebooted.

One of the advantages of persistent tunnels is that they eliminate the need for separate --up and --down scripts to run the appropriate ifconfig(8) and route(8) commands. These commands can be placed in the the same shell script which starts or terminates an OpenVPN session.

Another advantage is that open connections through the TUN/TAP-based tunnel will not be reset if the OpenVPN peer restarts. This can be useful to provide uninterrupted connectivity through the tunnel in the event of a DHCP reset of the peer's public IP address (see the --ipchange option above).

One disadvantage of persistent tunnels is that it is harder to automatically configure their MTU value (see --link-mtu and --tun-mtu above).

On some platforms such as Windows, TAP-Win32 tunnels are persistent by default.

--rmtun

(Standalone) Remove a persistent tunnel.

--dev tunX | tapX

TUN/TAP device

--user user

Optional user to be owner of this tunnel.

--group group

Optional group to be owner of this tunnel.

Windows-Specific Options:

--win-sys path

Set the Windows system directory pathname to use when looking for system executables such as route.exe and netsh.exe. By default, if this directive is not specified, OpenVPN will use the SystemRoot environment variable.

This option have changed behaviour in OpenVPN 2.3. Earlier you had to define --win-sys env to use the SystemRoot environment variable, otherwise it defaulted to C:\WINDOWS. It is not needed to use the env keyword any more, and it will just be ignored. A warning is logged when this is found in the configuration file.

--ip-win32 method

When using --ifconfig on Windows, set the TAP-Win32 adapter IP address and netmask using method. Don't use this option unless you are also using --ifconfig.

manual -- Don't set the IP address or netmask automatically. Instead output a message to the console telling the user to configure the adapter manually and indicating the IP/netmask which OpenVPN expects the adapter to be set to.

dynamic [offset] [lease-time] -- Automatically set the IP address and netmask by replying to DHCP query messages generated by the kernel. This mode is probably the "cleanest" solution for setting the TCP/IP properties since it uses the well-known DHCP protocol. There are, however, two prerequisites for using this mode: (1) The TCP/IP properties for the TAP-Win32 adapter must be set to "Obtain an IP address automatically," and (2) OpenVPN needs to claim an IP address in the subnet for use as the virtual DHCP server address. By default in --dev tap mode, OpenVPN will take the normally unused first address in the subnet. For example, if your subnet is 192.168.4.0 netmask 255.255.255.0, then OpenVPN will take the IP address 192.168.4.0 to use as the virtual DHCP server address. In --dev tun mode, OpenVPN will cause the DHCP server to masquerade as if it were coming from the remote endpoint. The optional offset parameter is an integer which is > -256 and < 256 and which defaults to -1. If offset is positive, the DHCP server will masquerade as the IP address at network address + offset. If offset is negative, the DHCP server will masquerade as the IP address at broadcast address + offset. The Windows ipconfig /all command can be used to show what Windows thinks the DHCP server address is. OpenVPN will "claim" this address, so make sure to use a free address. Having said that, different OpenVPN instantiations, including different ends of the same connection, can share the same virtual DHCP server address. The lease-time parameter controls the lease time of the DHCP assignment given to the TAP-Win32 adapter, and is denoted in seconds. Normally a very long lease time is preferred because it prevents routes involving the TAP-Win32 adapter from being lost when the system goes to sleep. The default lease time is one year.

netsh -- Automatically set the IP address and netmask using the Windows command-line "netsh" command. This method appears to work correctly on Windows XP but not Windows 2000.

ipapi -- Automatically set the IP address and netmask using the Windows IP Helper API. This approach does not have ideal semantics, though testing has indicated that it works okay in practice. If you use this option, it is best to leave the TCP/IP properties for the TAP-Win32 adapter in their default state, i.e. "Obtain an IP address automatically."

adaptive -- (Default) Try dynamic method initially and fail over to netsh if the DHCP negotiation with the TAP-Win32 adapter does not succeed in 20 seconds. Such failures have been known to occur when certain third-party firewall packages installed on the client machine block the DHCP negotiation used by the TAP-Win32 adapter. Note that if the netsh failover occurs, the TAP-Win32 adapter TCP/IP properties will be reset from DHCP to static, and this will cause future OpenVPN startups using the adaptive mode to use netsh immediately, rather than trying dynamic first. To "unstick" the adaptive mode from using netsh, run OpenVPN at least once using the dynamic mode to restore the TAP-Win32 adapter TCP/IP properties to a DHCP configuration.

--route-method m

Which method m to use for adding routes on Windows?

adaptive (default) -- Try IP helper API first. If that fails, fall back to the route.exe shell command.
ipapi -- Use IP helper API.
exe -- Call the route.exe shell command.

--dhcp-option type [parm]

Set extended TAP-Win32 TCP/IP properties, must be used with --ip-win32 dynamic or --ip-win32 adaptive. This option can be used to set additional TCP/IP properties on the TAP-Win32 adapter, and is particularly useful for configuring an OpenVPN client to access a Samba server across the VPN.

DOMAIN name -- Set Connection-specific DNS Suffix.

DNS addr -- Set primary domain name server IPv4 address. Repeat this option to set secondary DNS server addresses.

DNS6 addr -- Set primary domain name server IPv6 address. Repeat this option to set secondary DNS server IPv6 addresses.

Note: currently this is handled using netsh (the existing DHCP code can only do IPv4 DHCP, and that protocol only permits IPv4 addresses anywhere). The option will be put into the environment, so an --up script could act upon it if needed.

WINS addr -- Set primary WINS server address (NetBIOS over TCP/IP Name Server). Repeat this option to set secondary WINS server addresses.

NBDD addr -- Set primary NBDD server address (NetBIOS over TCP/IP Datagram Distribution Server) Repeat this option to set secondary NBDD server addresses.

NTP addr -- Set primary NTP server address (Network Time Protocol). Repeat this option to set secondary NTP server addresses.

NBT type -- Set NetBIOS over TCP/IP Node type. Possible options: 1 = b-node (broadcasts), 2 = p-node (point-to-point name queries to a WINS server), 4 = m-node (broadcast then query name server), and 8 = h-node (query name server, then broadcast).

NBS scope-id -- Set NetBIOS over TCP/IP Scope. A NetBIOS Scope ID provides an extended naming service for the NetBIOS over TCP/IP (Known as NBT) module. The primary purpose of a NetBIOS scope ID is to isolate NetBIOS traffic on a single network to only those nodes with the same NetBIOS scope ID. The NetBIOS scope ID is a character string that is appended to the NetBIOS name. The NetBIOS scope ID on two hosts must match, or the two hosts will not be able to communicate. The NetBIOS Scope ID also allows computers to use the same computer name, as they have different scope IDs. The Scope ID becomes a part of the NetBIOS name, making the name unique. (This description of NetBIOS scopes courtesy of NeonSurge@abyss.com)

DISABLE-NBT -- Disable Netbios-over-TCP/IP.

Note that if --dhcp-option is pushed via --push to a non-windows client, the option will be saved in the client's environment before the up script is called, under the name "foreign_option_{n}".

--tap-sleep n

Cause OpenVPN to sleep for n seconds immediately after the TAP-Win32 adapter state is set to "connected".

This option is intended to be used to troubleshoot problems with the --ifconfig and --ip-win32 options, and is used to give the TAP-Win32 adapter time to come up before Windows IP Helper API operations are applied to it.

--show-net-up

Output OpenVPN's view of the system routing table and network adapter list to the syslog or log file after the TUN/TAP adapter has been brought up and any routes have been added.

--block-outside-dns

Block DNS servers on other network adapters to prevent DNS leaks. This option prevents any application from accessing TCP or UDP port 53 except one inside the tunnel. It uses Windows Filtering Platform (WFP) and works on Windows Vista or later.

This option is considered unknown on non-Windows platforms and unsupported on Windows XP, resulting in fatal error. You may want to use --setenv opt or --ignore-unknown-option (not suitable for Windows XP) to ignore said error. Note that pushing unknown options from server does not trigger fatal errors.

--dhcp-renew

Ask Windows to renew the TAP adapter lease on startup. This option is normally unnecessary, as Windows automatically triggers a DHCP renegotiation on the TAP adapter when it comes up, however if you set the TAP-Win32 adapter Media Status property to "Always Connected", you may need this flag.

--dhcp-release

Ask Windows to release the TAP adapter lease on shutdown. This option has the same caveats as --dhcp-renew above.

--register-dns

Run ipconfig /flushdns and ipconfig /registerdns on connection initiation. This is known to kick Windows into recognizing pushed DNS servers.

--pause-exit

Put up a "press any key to continue" message on the console prior to OpenVPN program exit. This option is automatically used by the Windows explorer when OpenVPN is run on a configuration file using the right-click explorer menu.

--service exit-event [0|1]

Should be used when OpenVPN is being automatically executed by another program in such a context that no interaction with the user via display or keyboard is possible. In general, end-users should never need to explicitly use this option, as it is automatically added by the OpenVPN service wrapper when a given OpenVPN configuration is being run as a service.

exit-event is the name of a Windows global event object, and OpenVPN will continuously monitor the state of this event object and exit when it becomes signaled.

The second parameter indicates the initial state of exit-event and normally defaults to 0.

Multiple OpenVPN processes can be simultaneously executed with the same exit-event parameter. In any case, the controlling process can signal exit-event, causing all such OpenVPN processes to exit.

When executing an OpenVPN process using the --service directive, OpenVPN will probably not have a console window to output status/error messages, therefore it is useful to use --log or --log-append to write these messages to a file.

--show-adapters

(Standalone) Show available TAP-Win32 adapters which can be selected using the --dev-node option. On non-Windows systems, the ifconfig(8) command provides similar functionality.

--allow-nonadmin [TAP-adapter]

(Standalone) Set TAP-adapter to allow access from non-administrative accounts. If TAP-adapter is omitted, all TAP adapters on the system will be configured to allow non-admin access. The non-admin access setting will only persist for the length of time that the TAP-Win32 device object and driver remain loaded, and will need to be re-enabled after a reboot, or if the driver is unloaded and reloaded. This directive can only be used by an administrator.

--show-valid-subnets

(Standalone) Show valid subnets for --dev tun emulation. Since the TAP-Win32 driver exports an ethernet interface to Windows, and since TUN devices are point-to-point in nature, it is necessary for the TAP-Win32 driver to impose certain constraints on TUN endpoint address selection.

Namely, the point-to-point endpoints used in TUN device emulation must be the middle two addresses of a /30 subnet (netmask 255.255.255.252).

--show-net

(Standalone) Show OpenVPN's view of the system routing table and network adapter list.

PKCS#11 Standalone Options:

--show-pkcs11-ids [provider] [cert_private]

(Standalone) Show PKCS#11 token object list. Specify cert_private as 1 if certificates are stored as private objects.

If p11-kit is present on the system, the provider argument is optional; if omitted the default p11-kit-proxy.so module will be queried.

--verb option can be used BEFORE this option to produce debugging information.

Standalone Debug Options:

--show-gateway [v6target]: (Standalone) Show current IPv4 and IPv6 default gateway and interface towards the gateway (if the protocol in question is enabled). If an IPv6 address is passed as argument, the IPv6 route for this host is reported.

IPv6 Related Options

The following options exist to support IPv6 tunneling in peer-to-peer and client-server mode. All options are modeled after their IPv4 counterparts, so more detailed explanations given there apply here as well (except for --topology , which has no effect on IPv6).

--ifconfig-ipv6 ipv6addr/bits ipv6remote: configure IPv6 address ipv6addr/bits on the ``tun'' device. The second parameter is used as route target for --route-ipv6 if no gateway is specified.
--route-ipv6 ipv6addr/bits [gateway] [metric]: setup IPv6 routing in the system to send the specified IPv6 network into OpenVPN's ``tun''. The gateway parameter is only used for IPv6 routes across ``tap'' devices, and if missing, the ``ipv6remote'' field from --ifconfig-ipv6 is used.
--server-ipv6 ipv6addr/bits: convenience-function to enable a number of IPv6 related options at once, namely --ifconfig-ipv6, --ifconfig-ipv6-pool and --push tun-ipv6 Is only accepted if ``--mode server'' or ``--server'' is set. Pushing of the --tun-ipv6 directive is done for older clients which require an explicit ``--tun-ipv6'' in their configuration.
--ifconfig-ipv6-pool ipv6addr/bits: Specify an IPv6 address pool for dynamic assignment to clients. The pool starts at ipv6addr and matches the offset determined from the start of the IPv4 pool.
--ifconfig-ipv6-push ipv6addr/bits ipv6remote: for ccd/ per-client static IPv6 interface configuration, see --client-config-dir and --ifconfig-push for more details.
--iroute-ipv6 ipv6addr/bits: for ccd/ per-client static IPv6 route configuration, see --iroute for more details how to setup and use this, and how --iroute and --route interact.

SCRIPTING AND ENVIRONMENTAL VARIABLES

OpenVPN exports a series of environmental variables for use by user-defined scripts.

Script Order of Execution

--up: Executed after TCP/UDP socket bind and TUN/TAP open.
--tls-verify: Executed when we have a still untrusted remote peer.
--ipchange: Executed after connection authentication, or remote IP address change.
--client-connect: Executed in --mode server mode immediately after client authentication.
--route-up: Executed after connection authentication, either immediately after, or some number of seconds after as defined by the --route-delay option.
--route-pre-down: Executed right before the routes are removed.
--client-disconnect: Executed in --mode server mode on client instance shutdown.
--down: Executed after TCP/UDP and TUN/TAP close.
--learn-address: Executed in --mode server mode whenever an IPv4 address/route or MAC address is added to OpenVPN's internal routing table.
--auth-user-pass-verify: Executed in --mode server mode on new client connections, when the client is still untrusted.

String Types and Remapping

In certain cases, OpenVPN will perform remapping of characters in strings. Essentially, any characters outside the set of permitted characters for each string type will be converted to underbar ('_').

Q: Why is string remapping necessary?

A: It's an important security feature to prevent the malicious coding of strings from untrusted sources to be passed as parameters to scripts, saved in the environment, used as a common name, translated to a filename, etc.

Q: Can string remapping be disabled?

A: Yes, by using the --no-name-remapping option, however this should be considered an advanced option.

Here is a brief rundown of OpenVPN's current string types and the permitted character class for each string:

X509 Names: Alphanumeric, underbar ('_'), dash ('-'), dot ('.'), at ('@'), colon (':'), slash ('/'), and equal ('='). Alphanumeric is defined as a character which will cause the C library isalnum() function to return true.

Common Names: Alphanumeric, underbar ('_'), dash ('-'), dot ('.'), and at ('@').

--auth-user-pass username: Same as Common Name, with one exception: starting with OpenVPN 2.0.1, the username is passed to the OPENVPN_PLUGIN_AUTH_USER_PASS_VERIFY plugin in its raw form, without string remapping.

--auth-user-pass password: Any "printable" character except CR or LF. Printable is defined to be a character which will cause the C library isprint() function to return true.

--client-config-dir filename as derived from common name or username: Alphanumeric, underbar ('_'), dash ('-'), and dot ('.') except for "." or ".." as standalone strings. As of 2.0.1-rc6, the at ('@') character has been added as well for compatibility with the common name character class.

Environmental variable names: Alphanumeric or underbar ('_').

Environmental variable values: Any printable character.

For all cases, characters in a string which are not members of the legal character class for that string type will be remapped to underbar ('_').

Environmental Variables

Once set, a variable is persisted indefinitely until it is reset by a new value or a restart,

As of OpenVPN 2.0-beta12, in server mode, environmental variables set by OpenVPN are scoped according to the client objects they are associated with, so there should not be any issues with scripts having access to stale, previously set variables which refer to different client instances.

bytes_received

Total number of bytes received from client during VPN session. Set prior to execution of the --client-disconnect script.

bytes_sent

Total number of bytes sent to client during VPN session. Set prior to execution of the --client-disconnect script.

common_name

The X509 common name of an authenticated client. Set prior to execution of --client-connect, --client-disconnect, and --auth-user-pass-verify scripts.

config

Name of first --config file. Set on program initiation and reset on SIGHUP.

daemon

Set to "1" if the --daemon directive is specified, or "0" otherwise. Set on program initiation and reset on SIGHUP.

daemon_log_redirect

Set to "1" if the --log or --log-append directives are specified, or "0" otherwise. Set on program initiation and reset on SIGHUP.

dev

The actual name of the TUN/TAP device, including a unit number if it exists. Set prior to --up or --down script execution.

dev_idx

On Windows, the device index of the TUN/TAP adapter (to be used in netsh.exe calls which sometimes just do not work right with interface names). Set prior to --up or --down script execution.

foreign_option_{n}

An option pushed via --push to a client which does not natively support it, such as --dhcp-option on a non-Windows system, will be recorded to this environmental variable sequence prior to --up script execution.

ifconfig_broadcast

The broadcast address for the virtual ethernet segment which is derived from the --ifconfig option when --dev tap is used. Set prior to OpenVPN calling the ifconfig or netsh (windows version of ifconfig) commands which normally occurs prior to --up script execution.

ifconfig_ipv6_local

The local VPN endpoint IPv6 address specified in the --ifconfig-ipv6 option (first parameter). Set prior to OpenVPN calling the ifconfig or netsh (windows version of ifconfig) commands which normally occurs prior to --up script execution.

ifconfig_ipv6_netbits

The prefix length of the IPv6 network on the VPN interface. Derived from the /nnn parameter of the IPv6 address in the --ifconfig-ipv6 option (first parameter). Set prior to OpenVPN calling the ifconfig or netsh (windows version of ifconfig) commands which normally occurs prior to --up script execution.

ifconfig_ipv6_remote

The remote VPN endpoint IPv6 address specified in the --ifconfig-ipv6 option (second parameter). Set prior to OpenVPN calling the ifconfig or netsh (windows version of ifconfig) commands which normally occurs prior to --up script execution.

ifconfig_local

The local VPN endpoint IP address specified in the --ifconfig option (first parameter). Set prior to OpenVPN calling the ifconfig or netsh (windows version of ifconfig) commands which normally occurs prior to --up script execution.

ifconfig_remote

The remote VPN endpoint IP address specified in the --ifconfig option (second parameter) when --dev tun is used. Set prior to OpenVPN calling the ifconfig or netsh (windows version of ifconfig) commands which normally occurs prior to --up script execution.

ifconfig_netmask

The subnet mask of the virtual ethernet segment that is specified as the second parameter to --ifconfig when --dev tap is being used. Set prior to OpenVPN calling the ifconfig or netsh (windows version of ifconfig) commands which normally occurs prior to --up script execution.

ifconfig_pool_local_ip

The local virtual IP address for the TUN/TAP tunnel taken from an --ifconfig-push directive if specified, or otherwise from the ifconfig pool (controlled by the --ifconfig-pool config file directive). Only set for --dev tun tunnels. This option is set on the server prior to execution of the --client-connect and --client-disconnect scripts.

ifconfig_pool_netmask

The virtual IP netmask for the TUN/TAP tunnel taken from an --ifconfig-push directive if specified, or otherwise from the ifconfig pool (controlled by the --ifconfig-pool config file directive). Only set for --dev tap tunnels. This option is set on the server prior to execution of the --client-connect and --client-disconnect scripts.

ifconfig_pool_remote_ip

The remote virtual IP address for the TUN/TAP tunnel taken from an --ifconfig-push directive if specified, or otherwise from the ifconfig pool (controlled by the --ifconfig-pool config file directive). This option is set on the server prior to execution of the --client-connect and --client-disconnect scripts.

link_mtu

The maximum packet size (not including the IP header) of tunnel data in UDP tunnel transport mode. Set prior to --up or --down script execution.

local

The --local parameter. Set on program initiation and reset on SIGHUP.

local_port

The local port number or name, specified by --port or --lport. Set on program initiation and reset on SIGHUP.

password

The password provided by a connecting client. Set prior to --auth-user-pass-verify script execution only when the via-env modifier is specified, and deleted from the environment after the script returns.

proto

The --proto parameter. Set on program initiation and reset on SIGHUP.

remote_{n}

The --remote parameter. Set on program initiation and reset on SIGHUP.

remote_port_{n}

The remote port number, specified by --port or --rport. Set on program initiation and reset on SIGHUP.

route_net_gateway

The pre-existing default IP gateway in the system routing table. Set prior to --up script execution.

route_vpn_gateway

The default gateway used by --route options, as specified in either the --route-gateway option or the second parameter to --ifconfig when --dev tun is specified. Set prior to --up script execution.

route_{parm}_{n}

A set of variables which define each route to be added, and are set prior to --up script execution.

parm will be one of "network", "netmask", "gateway", or "metric".

n is the OpenVPN route number, starting from 1.

If the network or gateway are resolvable DNS names, their IP address translations will be recorded rather than their names as denoted on the command line or configuration file.

route_ipv6_{parm}_{n}

A set of variables which define each IPv6 route to be added, and are set prior to --up script execution.

parm will be one of "network" or "gateway" ("netmask" is contained as "/nnn" in the route_ipv6_network_{n}, unlike IPv4 where it is passed in a separate environment variable).

n is the OpenVPN route number, starting from 1.

If the network or gateway are resolvable DNS names, their IP address translations will be recorded rather than their names as denoted on the command line or configuration file.

peer_cert

Temporary file name containing the client certificate upon connection. Useful in conjunction with --tls-verify

script_context

Set to "init" or "restart" prior to up/down script execution. For more information, see documentation for --up.

script_type

Prior to execution of any script, this variable is set to the type of script being run. It can be one of the following: up, down, ipchange, route-up, tls-verify, auth-user-pass-verify, client-connect, client-disconnect, or learn-address. Set prior to execution of any script.

signal

The reason for exit or restart. Can be one of sigusr1, sighup, sigterm, sigint, inactive (controlled by --inactive option), ping-exit (controlled by --ping-exit option), ping-restart (controlled by --ping-restart option), connection-reset (triggered on TCP connection reset), error, or unknown (unknown signal). This variable is set just prior to down script execution.

time_ascii

Client connection timestamp, formatted as a human-readable time string. Set prior to execution of the --client-connect script.

time_duration

The duration (in seconds) of the client session which is now disconnecting. Set prior to execution of the --client-disconnect script.

time_unix

Client connection timestamp, formatted as a unix integer date/time value. Set prior to execution of the --client-connect script.

tls_digest_{n} / tls_digest_sha256_{n}

Contains the certificate SHA1 / SHA256 fingerprint, where n is the verification level. Only set for TLS connections. Set prior to execution of --tls-verify script.

tls_id_{n}

A series of certificate fields from the remote peer, where n is the verification level. Only set for TLS connections. Set prior to execution of --tls-verify script.

tls_serial_{n}

The serial number of the certificate from the remote peer, where n is the verification level. Only set for TLS connections. Set prior to execution of --tls-verify script. This is in the form of a decimal string like "933971680", which is suitable for doing serial-based OCSP queries (with OpenSSL, do not prepend "0x" to the string) If something goes wrong while reading the value from the certificate it will be an empty string, so your code should check that. See the contrib/OCSP_check/OCSP_check.sh script for an example.

tls_serial_hex_{n}

Like tls_serial_{n}, but in hex form (e.g. "12:34:56:78:9A").

tun_mtu

The MTU of the TUN/TAP device. Set prior to --up or --down script execution.

trusted_ip (or trusted_ip6)

Actual IP address of connecting client or peer which has been authenticated. Set prior to execution of --ipchange, --client-connect, and --client-disconnect scripts. If using ipv6 endpoints (udp6, tcp6), trusted_ip6 will be set instead.

trusted_port

Actual port number of connecting client or peer which has been authenticated. Set prior to execution of --ipchange, --client-connect, and --client-disconnect scripts.

untrusted_ip (or untrusted_ip6)

Actual IP address of connecting client or peer which has not been authenticated yet. Sometimes used to nmap the connecting host in a --tls-verify script to ensure it is firewalled properly. Set prior to execution of --tls-verify and --auth-user-pass-verify scripts. If using ipv6 endpoints (udp6, tcp6), untrusted_ip6 will be set instead.

untrusted_port

Actual port number of connecting client or peer which has not been authenticated yet. Set prior to execution of --tls-verify and --auth-user-pass-verify scripts.

username

The username provided by a connecting client. Set prior to --auth-user-pass-verify script execution only when the via-env modifier is specified.

X509_{n}_{subject_field}

An X509 subject field from the remote peer certificate, where n is the verification level. Only set for TLS connections. Set prior to execution of --tls-verify script. This variable is similar to tls_id_{n} except the component X509 subject fields are broken out, and no string remapping occurs on these field values (except for remapping of control characters to "_"). For example, the following variables would be set on the OpenVPN server using the sample client certificate in sample-keys (client.crt). Note that the verification level is 0 for the client certificate and 1 for the CA certificate.

X509_0_emailAddress=me@myhost.mydomain
X509_0_CN=Test-Client
X509_0_O=OpenVPN-TEST
X509_0_ST=NA
X509_0_C=KG
X509_1_emailAddress=me@myhost.mydomain
X509_1_O=OpenVPN-TEST
X509_1_L=BISHKEK
X509_1_ST=NA
X509_1_C=KG

INLINE FILE SUPPORT

OpenVPN allows including files in the main configuration for the --ca, --cert, --dh, --extra-certs, --key, --pkcs12, --secret, --crl-verify, --http-proxy-user-pass, --tls-auth and --tls-crypt options.

Each inline file started by the line <option> and ended by the line </option>

Here is an example of an inline file usage

<cert>
-----BEGIN CERTIFICATE-----
[...]
-----END CERTIFICATE-----
</cert>

When using the inline file feature with --pkcs12 the inline file has to be base64 encoded. Encoding of a .p12 file into base64 can be done for example with OpenSSL by running openssl base64 -in input.p12

SIGNALS

SIGHUP

Cause OpenVPN to close all TUN/TAP and network connections, restart, re-read the configuration file (if any), and reopen TUN/TAP and network connections.

SIGUSR1

Like SIGHUP, except don't re-read configuration file, and possibly don't close and reopen TUN/TAP device, re-read key files, preserve local IP address/port, or preserve most recently authenticated remote IP address/port based on --persist-tun, --persist-key, --persist-local-ip, and --persist-remote-ip options respectively (see above).

This signal may also be internally generated by a timeout condition, governed by the --ping-restart option.

This signal, when combined with --persist-remote-ip, may be sent when the underlying parameters of the host's network interface change such as when the host is a DHCP client and is assigned a new IP address. See --ipchange above for more information.

SIGUSR2

Causes OpenVPN to display its current statistics (to the syslog file if --daemon is used, or stdout otherwise).

SIGINT, SIGTERM

Causes OpenVPN to exit gracefully.

TUN/TAP DRIVER SETUP

If you are running Linux 2.4.7 or higher, you probably have the TUN/TAP driver already installed. If so, there are still a few things you need to do:

Make device: mknod /dev/net/tun c 10 200

Load driver: modprobe tun

EXAMPLES

Prior to running these examples, you should have OpenVPN installed on two machines with network connectivity between them. If you have not yet installed OpenVPN, consult the INSTALL file included in the OpenVPN distribution.

TUN/TAP Setup:

If you are using Linux 2.4 or higher, make the tun device node and load the tun module:

: mknod /dev/net/tun c 10 200

: modprobe tun

If you installed from RPM, the mknod step may be omitted, because the RPM install does that for you.

Only Linux 2.4 and newer are supported.

For other platforms, consult the INSTALL file at http://openvpn.net/install.html for more information.

Firewall Setup:

If firewalls exist between the two machines, they should be set to forward UDP port 1194 in both directions. If you do not have control over the firewalls between the two machines, you may still be able to use OpenVPN by adding --ping 15 to each of the openvpn commands used below in the examples (this will cause each peer to send out a UDP ping to its remote peer once every 15 seconds which will cause many stateful firewalls to forward packets in both directions without an explicit firewall rule).

If you are using a Linux iptables-based firewall, you may need to enter the following command to allow incoming packets on the TUN device:

: iptables -A INPUT -i tun+ -j ACCEPT

See the firewalls section below for more information on configuring firewalls for use with OpenVPN.

VPN Address Setup:

For purposes of our example, our two machines will be called bob.example.com and alice.example.com. If you are constructing a VPN over the internet, then replace bob.example.com and alice.example.com with the internet hostname or IP address that each machine will use to contact the other over the internet.

Now we will choose the tunnel endpoints. Tunnel endpoints are private IP addresses that only have meaning in the context of the VPN. Each machine will use the tunnel endpoint of the other machine to access it over the VPN. In our example, the tunnel endpoint for bob.example.com will be 10.4.0.1 and for alice.example.com, 10.4.0.2.

Once the VPN is established, you have essentially created a secure alternate path between the two hosts which is addressed by using the tunnel endpoints. You can control which network traffic passes between the hosts (a) over the VPN or (b) independently of the VPN, by choosing whether to use (a) the VPN endpoint address or (b) the public internet address, to access the remote host. For example if you are on bob.example.com and you wish to connect to alice.example.com via ssh without using the VPN (since ssh has its own built-in security) you would use the command ssh alice.example.com. However in the same scenario, you could also use the command telnet 10.4.0.2 to create a telnet session with alice.example.com over the VPN, that would use the VPN to secure the session rather than ssh.

You can use any address you wish for the tunnel endpoints but make sure that they are private addresses (such as those that begin with 10 or 192.168) and that they are not part of any existing subnet on the networks of either peer, unless you are bridging. If you use an address that is part of your local subnet for either of the tunnel endpoints, you will get a weird feedback loop.

Example 1: A simple tunnel without security

On bob:

: openvpn --remote alice.example.com --dev tun1 --ifconfig 10.4.0.1 10.4.0.2 --verb 9

On alice:

: openvpn --remote bob.example.com --dev tun1 --ifconfig 10.4.0.2 10.4.0.1 --verb 9

Now verify the tunnel is working by pinging across the tunnel.

On bob:

: ping 10.4.0.2

On alice:

: ping 10.4.0.1

The --verb 9 option will produce verbose output, similar to the tcpdump(8) program. Omit the --verb 9 option to have OpenVPN run quietly.

Example 2: A tunnel with static-key security (i.e. using a pre-shared secret)

First build a static key on bob.

: openvpn --genkey --secret key

This command will build a random key file called key (in ascii format). Now copy key to alice over a secure medium such as by using the scp(1) program.

On bob:

: openvpn --remote alice.example.com --dev tun1 --ifconfig 10.4.0.1 10.4.0.2 --verb 5 --secret key

On alice:

: openvpn --remote bob.example.com --dev tun1 --ifconfig 10.4.0.2 10.4.0.1 --verb 5 --secret key

Now verify the tunnel is working by pinging across the tunnel.

On bob:

: ping 10.4.0.2

On alice:

: ping 10.4.0.1

Example 3: A tunnel with full TLS-based security

For this test, we will designate bob as the TLS client and alice as the TLS server. Note that client or server designation only has meaning for the TLS subsystem. It has no bearing on OpenVPN's peer-to-peer, UDP-based communication model.

First, build a separate certificate/key pair for both bob and alice (see above where --cert is discussed for more info). Then construct Diffie Hellman parameters (see above where --dh is discussed for more info). You can also use the included test files client.crt, client.key, server.crt, server.key and ca.crt. The .crt files are certificates/public-keys, the .key files are private keys, and ca.crt is a certification authority who has signed both client.crt and server.crt. For Diffie Hellman parameters you can use the included file dh1024.pem. Note that all client, server, and certificate authority certificates and keys included in the OpenVPN distribution are totally insecure and should be used for testing only.

On bob:

: openvpn --remote alice.example.com --dev tun1 --ifconfig 10.4.0.1 10.4.0.2 --tls-client --ca ca.crt --cert client.crt --key client.key --reneg-sec 60 --verb 5

On alice:

: openvpn --remote bob.example.com --dev tun1 --ifconfig 10.4.0.2 10.4.0.1 --tls-server --dh dh1024.pem --ca ca.crt --cert server.crt --key server.key --reneg-sec 60 --verb 5

Now verify the tunnel is working by pinging across the tunnel.

On bob:

: ping 10.4.0.2

On alice:

: ping 10.4.0.1

Notice the --reneg-sec 60 option we used above. That tells OpenVPN to renegotiate the data channel keys every minute. Since we used --verb 5 above, you will see status information on each new key negotiation.

For production operations, a key renegotiation interval of 60 seconds is probably too frequent. Omit the --reneg-sec 60 option to use OpenVPN's default key renegotiation interval of one hour.

Routing:

Assuming you can ping across the tunnel, the next step is to route a real subnet over the secure tunnel. Suppose that bob and alice have two network interfaces each, one connected to the internet, and the other to a private network. Our goal is to securely connect both private networks. We will assume that bob's private subnet is 10.0.0.0/24 and alice's is 10.0.1.0/24.

First, ensure that IP forwarding is enabled on both peers. On Linux, enable routing:

: echo 1 > /proc/sys/net/ipv4/ip_forward

and enable TUN packet forwarding through the firewall:

: iptables -A FORWARD -i tun+ -j ACCEPT

On bob:

: route add -net 10.0.1.0 netmask 255.255.255.0 gw 10.4.0.2

On alice:

: route add -net 10.0.0.0 netmask 255.255.255.0 gw 10.4.0.1

Now any machine on the 10.0.0.0/24 subnet can access any machine on the 10.0.1.0/24 subnet over the secure tunnel (or vice versa).

In a production environment, you could put the route command(s) in a script and execute with the --up option.

FIREWALLS

OpenVPN's usage of a single UDP port makes it fairly firewall-friendly. You should add an entry to your firewall rules to allow incoming OpenVPN packets. On Linux 2.4+:

: iptables -A INPUT -p udp -s 1.2.3.4 --dport 1194 -j ACCEPT

This will allow incoming packets on UDP port 1194 (OpenVPN's default UDP port) from an OpenVPN peer at 1.2.3.4.

If you are using HMAC-based packet authentication (the default in any of OpenVPN's secure modes), having the firewall filter on source address can be considered optional, since HMAC packet authentication is a much more secure method of verifying the authenticity of a packet source. In that case:

: iptables -A INPUT -p udp --dport 1194 -j ACCEPT

would be adequate and would not render the host inflexible with respect to its peer having a dynamic IP address.

OpenVPN also works well on stateful firewalls. In some cases, you may not need to add any static rules to the firewall list if you are using a stateful firewall that knows how to track UDP connections. If you specify --ping n, OpenVPN will be guaranteed to send a packet to its peer at least once every n seconds. If n is less than the stateful firewall connection timeout, you can maintain an OpenVPN connection indefinitely without explicit firewall rules.

You should also add firewall rules to allow incoming IP traffic on TUN or TAP devices such as:

: iptables -A INPUT -i tun+ -j ACCEPT

to allow input packets from tun devices,

: iptables -A FORWARD -i tun+ -j ACCEPT

to allow input packets from tun devices to be forwarded to other hosts on the local network,

: iptables -A INPUT -i tap+ -j ACCEPT

to allow input packets from tap devices, and

: iptables -A FORWARD -i tap+ -j ACCEPT

to allow input packets from tap devices to be forwarded to other hosts on the local network.

These rules are secure if you use packet authentication, since no incoming packets will arrive on a TUN or TAP virtual device unless they first pass an HMAC authentication test.

FAQ

http://openvpn.net/faq.html

HOWTO

For a more comprehensive guide to setting up OpenVPN in a production setting, see the OpenVPN HOWTO at http://openvpn.net/howto.html

PROTOCOL

For a description of OpenVPN's underlying protocol, see http://openvpn.net/security.html

WEB

OpenVPN's web site is at http://openvpn.net/

Go here to download the latest version of OpenVPN, subscribe to the mailing lists, read the mailing list archives, or browse the SVN repository.

BUGS

Report all bugs to the OpenVPN team <info@openvpn.net>.

NOTES

This product includes software developed by the OpenSSL Project ( http://www.openssl.org/ )

For more information on the TLS protocol, see http://www.ietf.org/rfc/rfc2246.txt

For more information on the LZO real-time compression library see http://www.oberhumer.com/opensource/lzo/

COPYRIGHT

Copyright (C) 2002-2010 OpenVPN Technologies, Inc. This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License version 2 as published by the Free Software Foundation.