www.LinuxHowtos.org
LSBLK
Section: System Administration (8)Updated: February 2013
Index Return to Main Contents
NAME
lsblk - list block devicesSYNOPSIS
lsblk [options] [device...]DESCRIPTION
lsblk lists information about all available or the specified block devices. The lsblk command reads the sysfs filesystem and udev db to gather information.The command prints all block devices (except RAM disks) in a tree-like format by default. Use lsblk --help to get a list of all available columns.
The default output, as well as the default output from options like --fs and --topology, is subject to change. So whenever possible, you should avoid using default outputs in your scripts. Always explicitly define expected columns by using --output columns-list in environments where a stable output is required.
Note that lsblk might be executed in time when udev does not have all information about recently added or modified devices yet. In this case it is recommended to use udevadm settle before lsblk to synchronize with udev.
OPTIONS
- -a, --all
- Also list empty devices. (By default they are skipped.)
- -b, --bytes
- Print the SIZE column in bytes rather than in a human-readable format.
- -D, --discard
- Print information about the discarding capabilities (TRIM, UNMAP) for each device.
- -z, --zoned
- Print the zone model for each device.
- -d, --nodeps
- Do not print holder devices or slaves. For example, lsblk --nodeps /dev/sda prints information about the sda device only.
- -e, --exclude list
- Exclude the devices specified by the comma-separated list of major device numbers. Note that RAM disks (major=1) are excluded by default. The filter is applied to the top-level devices only.
- -f, --fs
- Output info about filesystems. This option is equivalent to -o NAME,FSTYPE,LABEL,UUID,MOUNTPOINT. The authoritative information about filesystems and raids is provided by the blkid(8) command.
- -h, --help
- Display help text and exit.
- -I, --include list
- Include devices specified by the comma-separated list of major device numbers. The filter is applied to the top-level devices only.
- -i, --ascii
- Use ASCII characters for tree formatting.
- -J, --json
- Use JSON output format.
- -l, --list
- Produce output in the form of a list.
- -m, --perms
- Output info about device owner, group and mode. This option is equivalent to -o NAME,SIZE,OWNER,GROUP,MODE.
- -n, --noheadings
- Do not print a header line.
- -o, --output list
-
Specify which output columns to print. Use
--help
to get a list of all supported columns.
The default list of columns may be extended if list is specified in the format +list (e.g. lsblk -o +UUID).
- -O, --output-all
- Output all available columns.
- -P, --pairs
- Produce output in the form of key="value" pairs. All potentially unsafe characters are hex-escaped (\x<code>).
- -p, --paths
- Print full device paths.
- -r, --raw
- Produce output in raw format. All potentially unsafe characters are hex-escaped (\x<code>) in the NAME, KNAME, LABEL, PARTLABEL and MOUNTPOINT columns.
- -S, --scsi
- Output info about SCSI devices only. All partitions, slaves and holder devices are ignored.
- -s, --inverse
- Print dependencies in inverse order. If the --list output is requested then the lines are still ordered by dependencies.
- -t, --topology
- Output info about block-device topology. This option is equivalent to -o NAME,ALIGNMENT,MIN-IO,OPT-IO,PHY-SEC,LOG-SEC,ROTA,SCHED,RQ-SIZE,RA,WSAME.
- -V, --version
- Display version information and exit.
- -x, --sort column
- Sort output lines by column. This option enables --list output.
NOTES
For partitions, some information (e.g. queue attributes) is inherited from the parent device.The lsblk command needs to be able to look up each block device by major:minor numbers, which is done by using /sys/dev/block. This sysfs block directory appeared in kernel 2.6.27 (October 2008). In case of problems with a new enough kernel, check that CONFIG_SYSFS was enabled at the time of the kernel build.
RETURN CODES
- 0
- success
- 1
- failure
- 32
- not found all specified devices
- 64
-
some specified devices found, some not found
AUTHORS
Milan Broz <mbroz@redhat.com> Karel Zak <kzak@redhat.com>
ENVIRONMENT
- LIBBLKID_DEBUG=all
- enables libblkid debug output.
- LIBMOUNT_DEBUG=all
- enables libmount debug output.
- LIBSMARTCOLS_DEBUG=all
- enables libsmartcols debug output.
- LIBSMARTCOLS_DEBUG_PADDING=on
- use visible padding characters. Requires enabled LIBSMARTCOLS_DEBUG.
SEE ALSO
ls(1), blkid(8), findmnt(8)AVAILABILITY
The lsblk command is part of the util-linux package and is available from https://www.kernel.org/pub/linux/utils/util-linux/.