from small one page howto to huge articles all in one place
 

search text in:





Poll
What does your sytem tell when running "ulimit -u"?








poll results

Last additions:
using iotop to find disk usage hogs

using iotop to find disk usage hogs

words:

887

views:

196714

userrating:

average rating: 1.7 (102 votes) (1=very good 6=terrible)


May 25th. 2007:
Words

486

Views

252324

why adblockers are bad


Workaround and fixes for the current Core Dump Handling vulnerability affected kernels

Workaround and fixes for the current Core Dump Handling vulnerability affected kernels

words:

161

views:

141294

userrating:

average rating: 1.4 (42 votes) (1=very good 6=terrible)


April, 26th. 2006:

Druckversion
You are here: manpages





CHMEM

Section: System Administration (8)
Updated: October 2016
Index Return to Main Contents
 

NAME

chmem - configure memory  

SYNOPSIS

chmem [-h] [-V] [-v] [-e|-d] [SIZE|RANGE|-b BLOCKRANGE]  

DESCRIPTION

The chmem command sets a particular size or range of memory online or offline.
-
Specify SIZE as <size>[m|M|g|G]. With m or M, <size> specifies the memory size in MiB (1024 x 1024 bytes). With g or G, <size> specifies the memory size in GiB (1024 x 1024 x 1024 bytes). The default unit is MiB.
-
Specify RANGE in the form 0x<start>-0x<end> as shown in the output of the lsmem command. <start> is the hexadecimal address of the first byte and <end> is the hexadecimal address of the last byte in the memory range.
-
Specify BLOCKRANGE in the form <first>-<last> or <block> as shown in the output of the lsmem command. <first> is the number of the first memory block and <last> is the number of the last memory block in the memory range. Alternatively a single block can be specified. BLOCKRANGE requires the --blocks option.

SIZE and RANGE must be aligned to the Linux memory block size, as shown in the output of the lsmem command.

Setting memory online can fail for various reasons. On virtualized systems it can fail if the hypervisor does not have enough memory left, for example because memory was overcommitted. Setting memory offline can fail if Linux cannot free the memory. If only part of the requested memory can be set online or offline, a message tells you how much memory was set online or offline instead of the requested amount.

When setting memory online chmem starts with the lowest memory block numbers. When setting memory offline chmem starts with the highest memory block numbers.  

OPTIONS

-b, --blocks
Use a BLOCKRANGE parameter instead of RANGE or SIZE for the --enable and --disable options.
-d, --disable
Set the specified RANGE, SIZE, or BLOCKRANGE of memory offline.
-e, --enable
Set the specified RANGE, SIZE, or BLOCKRANGE of memory online.
-h, --help
Print a short help text, then exit.
-v, --verbose
Verbose mode. Causes chmem to print debugging messages about it's progress.
-V, --version
Print the version number, then exit.
 

RETURN CODES

chmem has the following return codes:
0
success
1
failure
64
partial success
 

EXAMPLES

chmem --enable 1024
This command requests 1024 MiB of memory to be set online.
chmem -e 2g
This command requests 2 GiB of memory to be set online.
chmem --disable 0x00000000e4000000-0x00000000f3ffffff
This command requests the memory range starting with 0x00000000e4000000 and ending with 0x00000000f3ffffff to be set offline.
chmem -b -d 10
This command requests the memory block number 10 to be set offline.
 

SEE ALSO

lsmem(1)  

AVAILABILITY

The chmem command is part of the util-linux package and is available from Linux Kernel Archive


 

Index

NAME
SYNOPSIS
DESCRIPTION
OPTIONS
RETURN CODES
EXAMPLES
SEE ALSO
AVAILABILITY





Support us on Content Nation
rdf newsfeed | rss newsfeed | Atom newsfeed
- Powered by LeopardCMS - Running on Gentoo -
Copyright 2004-2020 Sascha Nitsch Unternehmensberatung GmbH
Valid XHTML1.1 : Valid CSS : buttonmaker
- Level Triple-A Conformance to Web Content Accessibility Guidelines 1.0 -
- Copyright and legal notices -
Time to create this page: 30.3 ms