www.LinuxHowtos.org howtos, tips&tricks and tutorials for linux

from small one page howto to huge articles all in one place

Other .linuxhowtos.org sites:toolsntoys.linuxhowtos.org
gentoo.linuxhowtos.org

poll results

Last additions:

using iotop to find disk usage hogs

words:

887

views:

196714

userrating:

average rating: 1.7 (102 votes) (1=very good 6=terrible)

May 25th. 2007:

Words

486

Views

252324

why adblockers are bad

Workaround and fixes for the current Core Dump Handling vulnerability affected kernels

words:

161

views:

141294

userrating:

average rating: 1.4 (42 votes) (1=very good 6=terrible)

April, 26th. 2006:

Words

Views

101157

New subdomain: toolsntoys.linuxhowtos.org

You are here: manpages

STRTOL

Section: Linux Programmer's Manual (3)
Updated: 2017-09-15
Index Return to Main Contents

NAME

strtol, strtoll, strtoq - convert a string to a long integer

SYNOPSIS

#include <stdlib.h>

long int strtol(const char *nptr, char **endptr, int base);

long long int strtoll(const char *nptr, char **endptr, int base);

Feature Test Macro Requirements for glibc (see feature_test_macros(7)):

strtoll():

: _ISOC99_SOURCE
|| /* Glibc versions <= 2.19: */ _SVID_SOURCE || _BSD_SOURCE

DESCRIPTION

The strtol() function converts the initial part of the string in nptr to a long integer value according to the given base, which must be between 2 and 36 inclusive, or be the special value 0.

The string may begin with an arbitrary amount of white space (as determined by isspace(3)) followed by a single optional aq+aq or aq-aq sign. If base is zero or 16, the string may then include a "0x" or "0X" prefix, and the number will be read in base 16; otherwise, a zero base is taken as 10 (decimal) unless the next character is aq0aq, in which case it is taken as 8 (octal).

The remainder of the string is converted to a long int value in the obvious manner, stopping at the first character which is not a valid digit in the given base. (In bases above 10, the letter aqAaq in either uppercase or lowercase represents 10, aqBaq represents 11, and so forth, with aqZaq representing 35.)

If endptr is not NULL, strtol() stores the address of the first invalid character in *endptr. If there were no digits at all, strtol() stores the original value of nptr in *endptr (and returns 0). In particular, if *nptr is not aq\0aq but **endptr is aq\0aq on return, the entire string is valid.

The strtoll() function works just like the strtol() function but returns a long long integer value.

RETURN VALUE

The strtol() function returns the result of the conversion, unless the value would underflow or overflow. If an underflow occurs, strtol() returns LONG_MIN. If an overflow occurs, strtol() returns LONG_MAX. In both cases, errno is set to ERANGE. Precisely the same holds for strtoll() (with LLONG_MIN and LLONG_MAX instead of LONG_MIN and LONG_MAX).

ERRORS

EINVAL: (not in C99) The given base contains an unsupported value.
ERANGE: The resulting value was out of range.

The implementation may also set errno to EINVAL in case no conversion was performed (no digits seen, and 0 returned).

ATTRIBUTES

For an explanation of the terms used in this section, see attributes(7).

Interface	Attribute	Value
strtol(), strtoll(), strtoq()	Thread safety	MT-Safe locale

CONFORMING TO

strtol(): POSIX.1-2001, POSIX.1-2008, C89, C99 SVr4, 4.3BSD.

strtoll(): POSIX.1-2001, POSIX.1-2008, C99.

NOTES

Since strtol() can legitimately return 0, LONG_MAX, or LONG_MIN (LLONG_MAX or LLONG_MIN for strtoll()) on both success and failure, the calling program should set errno to 0 before the call, and then determine if an error occurred by checking whether errno has a nonzero value after the call.

According to POSIX.1, in locales other than the "C" and "POSIX", these functions may accept other, implementation-defined numeric strings.

BSD also has

quad_t strtoq(const char *nptr, char **endptr, int base);

with completely analogous definition. Depending on the wordsize of the current architecture, this may be equivalent to strtoll() or to strtol().

EXAMPLE

The program shown below demonstrates the use of strtol(). The first command-line argument specifies a string from which strtol() should parse a number. The second (optional) argument specifies the base to be used for the conversion. (This argument is converted to numeric form using atoi(3), a function that performs no error checking and has a simpler interface than strtol().) Some examples of the results produced by this program are the following:

$ ./a.out 123 strtol() returned 123 $ ./a.out aq 123aq strtol() returned 123 $ ./a.out 123abc strtol() returned 123 Further characters after number: abc $ ./a.out 123abc 55 strtol: Invalid argument $ ./a.out aqaq No digits were found $ ./a.out 4000000000 strtol: Numerical result out of range

Program source

#include <stdlib.h> #include <limits.h> #include <stdio.h> #include <errno.h>

int main(int argc, char *argv[]) {
    int base;
    char *endptr, *str;
    long val;

    if (argc < 2) {
        fprintf(stderr, "Usage: %s str [base]\n", argv[0]);
        exit(EXIT_FAILURE);
    }

str = argv[1];
base = (argc > 2) ? atoi(argv[2]) : 10;

errno = 0; /* To distinguish success/failure after call */
val = strtol(str, &endptr, base);

/* Check for various possible errors */

    if ((errno == ERANGE && (val == LONG_MAX || val == LONG_MIN))
            || (errno != 0 && val == 0)) {
        perror("strtol");
        exit(EXIT_FAILURE);
    }

    if (endptr == str) {
        fprintf(stderr, "No digits were found\n");
        exit(EXIT_FAILURE);
    }

/* If we got here, strtol() successfully parsed a number */

printf("strtol() returned %ld\n", val);

if (*endptr != aq\0aq) /* Not necessarily an error... */
printf("Further characters after number: %s\n", endptr);

exit(EXIT_SUCCESS); }

COLOPHON

This page is part of release 4.13 of the Linux man-pages project. A description of the project, information about reporting bugs, and the latest version of this page, can be found at https://www.kernel.org/doc/man-pages/.